PURPOSE:The N-700 is an active electronic noise suppressor that employs a high density, low loss toroid 0.25 mH choke coupled with two power 2N3055 NPN power transistors in a capacitor multiplier configuration. The N-700 is designed to eliminate in-noise for Auto-sound Systems including: Alternator Whine, Fan Humming, ignition pops, etc.N-700 applications include Power Equalizers, Amplifiers, Cellular Phones, CB Radios, Two Way Communication Equipment, Amateur Radio Components, CD Players, and AM/FM Cassette Decks, etc. FEATURES:The air cooled design of the N-700 filter permits maximum efficiency and effectiveness.The ferrite toroid core of the choke component of the L configuration is responsible for a very high rate of attenuation with very low line losses.The Beta of the power transistors multiples the capacitance to maximize the attenuation of the active filter. There are only three wires needed for the installation of the filter =Filter Input, Filter Output, and the Chassis Ground.The Chassis Ground is required to complete the circuit’s operation. INSTALLATION:Make sure the noise is in-line before installing any in-line filter.A good confirmation would be to temporarily substitute a 120 VAC to a 12 VDC power supply, or a small 12 Volt motorcycle battery, for the vehicle's electrical system.If the noise goes away when the alternate power supply is connected, then you have a case of in-line noise. To get optimum results with the N-700, the following directions should be followed: 1.Cut the component's main power lead between the fuse and the component. 2. Connect the GREEN wire to the fuse side of the cut (Source). If no fuse is present, be sure to add a fuse to this connection. Be sure to add a fuse rated at 10 Amps or less to protect the vehicle. 3.Connect the RED wire to the component side (Load). This output lead is also fused to protect the N-700. 4.Connect the BLACK wire to a good chassis ground.The N-700 will not function without a connection to chassis ground. Practical and easy to install, the N-700 is one of the most versatile and effective filters on the market.
Iron powder cores are more stable than ferrites and do not saturate as easily so they are best for tuned circuits, filters, and high power inductors. They come in different “Mixes” for use at different frequencies. For best “Q” use the Mix specified for your frequency.To find the number of turns to give the desired inductance for your coil use the formula below:
Turns = 100 x 
Toroid Dimensions
To order specify core size and mix (e.g. T200A-2). Available in sizes that have µH per 100 turns shown in table.
All iron powder cores are special orders. Please allow one week for shipment after order received.
The iron powder cores shown in the above tables are primarily used for either high power feed line chokes for common mode current reduction or for 4:1 and 9;1 very high power transmission line transformers.
For high power feed line chokes, choose the inside diameter of the iron powder core closest to the transmission line outside diameter and use 6-20 cores at the junction with the antenna feed.
For 4:1 (50/200 or 75/300 ohm) transmission line transformers in the range of 1.8-30 Mhz, select the size appropriate for the power level as follows:
T200A x 2 = 1.5KW
T300A x 2 = 2.5KW
T400A x 2 = 5KW
Use Mix 2 for all the above transmission line transformers. Fully assembled and enclosed units are available for each of the power levels. Click HERE for information.
4:1 transmission line transformers using iron powder cores are typically used for ladder line to 50 ohm coax connections
For .1 – 2 Mhz wide band transformers use Mix 26 which has a higher permeability and requires less turns to achieve a given inductance. Mix 2 has almost constant permeability from 1-30 Mhz. Mix 26 has an initial permeability of 75 at .1 Mhz and gradually decreases to about 10 at 30 Mhz. For high power AM broadcast range (.5-1.7 Mhz) transformer, use Mix 26 to reduce the turn count.
Minimum order for iron powder cores is $50
Shipping on larger cores in quantity may be more than $10 – email/call for quote.