5:1 CUBE™ Unun – Model CU-5-1500 (50:250 Ohm, 1.8-61 MHz, 1.5KW PEP)
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 unun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical application:
Also available as a balanced output – CB-5-1500
Yaesu FTDX10 Transceiver RFI Kit - 8 RFI/Noise Reduction FiltersProduct DetailsMPN: RFI-YAESU-991Type: NEWCountry/Region of Manufacture: United StatesFilter Power Rating (PEP watts): 1500RFI Suppression Range (MHz): 1-300 MHz# Ferrite Filters: 8 (2 ring, 6 snap-on)Enclosure Size (inches): n/aTypical Use:: DC power, RF output(2), 5 additional I/O linesBUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH MANY BRANDS OF HAM/COMMERCIAL HF RADIOS WITH DUAL ANTENNAS OUTPUTS AND MULTIPLE I/O CONNECTIONS INCLUDING THE YAESU FTDX10
Kit Includes noise reduction ring filters for one coax cable, AC/DC power and six 1/2" snap on filters for I/O cables covering RFI range of 1-300 MHz. Quick installation - immediate RFI/noise reduction. No radio mods required.
This kit will help reduce or eliminate:
1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.
2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.
3. RFI to your other radios, audio/video systems, computers, telephones, etc.
A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).
These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.
The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.
Use of the chokes often helps cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.
For additional RFI suppression, use a feed line choke at the antenna feed point to suppress common current on the coax feed line and a coax noise filter (like our CMNF-500-50) at the radio end of the coax to reduce common mode noise.
If you use a linear amplifier use a Palomar Engineers amplifier RFI kit for additional RFI interference suppression.
On Sale
RG-8X Coax Jumper Cable with PL-259's on each end - 3 feetRG-8X Coax Jumper Cable with PL-259's on each end - 3 feetSKU RG-8X-3List price $19.95 Save 15%$16.95
BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH MANY BRANDS OF HAM/COMMERCIAL HF RADIOS WITH DUAL ANTENNAS OUTPUTS AND MULTIPLE I/O CONNECTIONS INCLUDING THE YAESU FTDX10
Kit Includes noise reduction ring filters for one coax cable, AC/DC power and six 1/2" snap on filters for I/O cables covering RFI range of 1-300 MHz. Quick installation - immediate RFI/noise reduction. No radio mods required.
This kit will help reduce or eliminate:
1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.
2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.
3. RFI to your other radios, audio/video systems, computers, telephones, etc.
A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).
These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.
The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.
Use of the chokes often helps cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.
For additional RFI suppression, use a feed line choke at the antenna feed point to suppress common current on the coax feed line and a coax noise filter (like our CMNF-500-50) at the radio end of the coax to reduce common mode noise.If you use a linear amplifier use a Palomar Engineers amplifier RFI kit for additional RFI interference suppression.
