5:1 CUBE™ Unun – Model CU-5-1500 (50:250 Ohm, 1.8-61 MHz, 1.5KW PEP)
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 unun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical application:
Also available as a balanced output – CB-5-1500
SABRE 50:100 (2:1) CUBE™ Balun (1.8-31 MHz), 2KW Top Studs OutputProduct Details
.
SPECIAL ORDER SABRE 2:1 CUBE Balun™ – (1.8-30 MHz)
(Original product part # was 770013S - circa 1999)
Model SABRE-2-2000 is a 2:1 (100:50) quad core balun used to translate a 50 ohm input to 100 ohms at RF power levels up to 2000 watts PEP when used with a matched load. This assembled balun features a quad core configuration for increased power handling and flatter frequency response to 31 MHz. With a matched 100 ohm load the SWR over the frequency range 1.8 to 30 MHz is shown in the following table measured with an AIM 4170 network analyzer. Notice that the conversion from 100 to 50 ohms is very consistent from 1.8-31 Mhz and SWR is less than 1.5:1 over the range allowing easy tuning by most radio internal antenna tuners or an external tuner. Graph is for a 2:1 balun often used with delta loop, log periodic, horizontal loop antennas and HF Radar.
Input connector is 50 ohm type N (SO-239 also available - inquire).SABRE-2-2000 is in a NEMA 4x4x2 weatherproof box with mounting flanges at bottom to attach to fixed location (mast, wall, beam antenna, etc.).
Eye bolts and studs are all stainless steel for long life.
SABRE 50:100 (2:1) CUBE™ Balun (1.8-31 MHz), 2KW Top Studs Output
Product Details
SPECIAL ORDER SABRE 2:1 CUBE Balun™ – (1.8-30 MHz)
(Original product part # was 770013S - circa 1999)
Model SABRE-2-2000 is a 2:1 (100:50) quad core balun used to translate a 50 ohm input to 100 ohms at RF power levels up to 2000 watts PEP when used with a matched load. This assembled balun features a quad core configuration for increased power handling and flatter frequency response to 31 MHz. With a matched 100 ohm load the SWR over the frequency range 1.8 to 30 MHz is shown in the following table measured with an AIM 4170 network analyzer. Notice that the conversion from 100 to 50 ohms is very consistent from 1.8-31 Mhz and SWR is less than 1.5:1 over the range allowing easy tuning by most radio internal antenna tuners or an external tuner. Graph is for a 2:1 balun often used with delta loop, log periodic, horizontal loop antennas and HF Radar.
Input connector is 50 ohm type N (SO-239 also available - inquire).SABRE-2-2000 is in a NEMA 4x4x2 weatherproof box with mounting flanges at bottom to attach to fixed location (mast, wall, beam antenna, etc.).
Eye bolts and studs are all stainless steel for long life.
