5:1 CUBE™ Unun – Model CU-5-1500 (50:250 Ohm, 1.8-61 MHz, 1.5KW PEP)
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 unun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical application:
Also available as a balanced output – CB-5-1500
Icom A220 A220T VHF Aircraft Transceiver RFI Kit - 2 Noise Reduction FiltersProduct DetailsMPN: RFI-ICOM-A220Type: NEWCountry/Region of Manufacture: United StatesFilter Power Rating (PEP watts): = Cable RatingRFI Suppression Range (MHz): 1-300 MHz# Ferrite Filters: 2Enclosure Size (inches): n/aTypical Use:: 15 Pin Plug, Antenna CoaxBUY THIS KIT NOW TO SOLVE YOUR RFI PROBLEMS! WORKS WITH MANY BRANDS OF COMMERCIAL VHF RADIOS INCLUDING ICOM A120, A220, A220T.
Quick installation - immediate RFI/noise reduction. No radio mods required.
This kit will help reduce or eliminate:
1. Radio Frequency Interference (RFI) to electronic devices including instrumentation and GPS systems.
2. RFI from other electronic devices such as switching power supplies, LED instrument and cockpit lights, battery chargers, GPS and computer systems which generate common mode currents on your radio interface or coaxial antenna feed lines.
3. These filters help reduce SWR problems between transceiver and antenna. The DC power line filter helps keep common mode current out of the power line which could cause interference to other devices connected to the same power source.
These chokes use a ferrite core material that is effective in suppressing RFI from transmitters and receivers experiencing a high noise floor in the 1-300 MHz range.
The ferrite split bead filters are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.
Kit Includes 2 noise reduction split bead (they snap on like a clam shell) filters for coax and AC/DC power/ standard 15 Pin connector cable. 3/4" whole ID - just wrap 2-3 turns of coax cable thru 1 bead and 2-3 turns of the DC power/15 Pin cable thru the other split bead. Does not affect signals carried by the cables, only the common mode interference noise is suppressed.
For additional RFI suppression, use a feed line choke at the antenna feed point to suppress common current on the coax feed line during TRANSMIT and a CMNF-500-50 coax noise filter at the radio end of the coax to reduce common mode noise during RECEIVE.
Visit our website for all your RFI needs!
Note: Icom A220 radio shown NOT included in this kit.
BUY THIS KIT NOW TO SOLVE YOUR RFI PROBLEMS! WORKS WITH MANY BRANDS OF COMMERCIAL VHF RADIOS INCLUDING ICOM A120, A220, A220T.
Quick installation - immediate RFI/noise reduction. No radio mods required.
This kit will help reduce or eliminate:
1. Radio Frequency Interference (RFI) to electronic devices including instrumentation and GPS systems.
2. RFI from other electronic devices such as switching power supplies, LED instrument and cockpit lights, battery chargers, GPS and computer systems which generate common mode currents on your radio interface or coaxial antenna feed lines.
3. These filters help reduce SWR problems between transceiver and antenna. The DC power line filter helps keep common mode current out of the power line which could cause interference to other devices connected to the same power source.
These chokes use a ferrite core material that is effective in suppressing RFI from transmitters and receivers experiencing a high noise floor in the 1-300 MHz range.
The ferrite split bead filters are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.
Kit Includes 2 noise reduction split bead (they snap on like a clam shell) filters for coax and AC/DC power/ standard 15 Pin connector cable. 3/4" whole ID - just wrap 2-3 turns of coax cable thru 1 bead and 2-3 turns of the DC power/15 Pin cable thru the other split bead. Does not affect signals carried by the cables, only the common mode interference noise is suppressed.
For additional RFI suppression, use a feed line choke at the antenna feed point to suppress common current on the coax feed line during TRANSMIT and a CMNF-500-50 coax noise filter at the radio end of the coax to reduce common mode noise during RECEIVE.
Visit our website for all your RFI needs!
Note: Icom A220 radio shown NOT included in this kit.
