5:1 CUBE™ Unun – Model CU-5-1500 (50:250 Ohm, 1.8-61 MHz, 1.5KW PEP)
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 unun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical application:
Also available as a balanced output – CB-5-1500
Hybrid 2:25 Current Balun + 1:1 Current Balun in one enclosure, 1.8-61 MHz, 1.5/5KW PEP - Loop AntennaProduct DetailsMPN: CB-2.25-1-1500/5000EB or TS optionCountry/Region of Manufacture: USAInput ohms/Output ohms: 50 in/112.5 outFrequency Range < 2:1 SWR (MHz): 1.8-61 MHzPEP Power Rating (watts): 1.5KW or 5KWEnclosure Size: 4"x4"x 2"(1.5KW), 6"x6"x4" (5KW)Weight (pounds): 3 (1.5KW), 5 (5KW)Antenna Compatability: Single Band Loop
After many requests we have created a compact, special balun for single band loop (Sky loop or Delta loop) antennas. The CB-2.25-1500 is a CUBE(TM) enclosure containing a multi-core, broadband 2:25 impedance transformer (50 ohm coax input to 112.5 ohm balanced output) in series with a 1:1 current balun for extra common mode current choking to keep RF current off the outside of the coax braid and on the antenna where it belongs. The extra choking action also means that the coax feed line will not act as a radiator causing unnecessary RF interference (RFI). Rated for full 1500 watts PEP and 450 watts CW (ICAS). 1.8Mhz – 61 MHz.
CB-2.25-1-1500EB is housed in a 4” x 4” x 2” waterproof housing with SO-239 input and stainless steel eye bolts on the side for ease of connection to your wire antenna. Top eye bolt acts as an antenna hoist. Also available with top studs for post or wall mounting (Model # CB-2.25-1-1500TS)
Loop antennas should be cut for 1005/F(MHz) in total length, where F (MHz) is the lowest frequency to be used. For 3.5MHz this equates to 288 foot perimeter (square, delta, multi-side ok).
Production Note: These hybrid baluns are special order and made to order for each customer. Please note that shipping will be approximately 2-3 weeks after order placed depending upon our existing production schedule.
Pictures show 2-1 balun but you will receive the 2.25:1 balun with 1:1 hybrid in a single enclosure.
After many requests we have created a compact, special balun for single band loop (Sky loop or Delta loop) antennas. The CB-2.25-1500 is a CUBE(TM) enclosure containing a multi-core, broadband 2:25 impedance transformer (50 ohm coax input to 112.5 ohm balanced output) in series with a 1:1 current balun for extra common mode current choking to keep RF current off the outside of the coax braid and on the antenna where it belongs. The extra choking action also means that the coax feed line will not act as a radiator causing unnecessary RF interference (RFI). Rated for full 1500 watts PEP and 450 watts CW (ICAS). 1.8Mhz – 61 MHz.
CB-2.25-1-1500EB is housed in a 4” x 4” x 2” waterproof housing with SO-239 input and stainless steel eye bolts on the side for ease of connection to your wire antenna. Top eye bolt acts as an antenna hoist. Also available with top studs for post or wall mounting (Model # CB-2.25-1-1500TS)
Loop antennas should be cut for 1005/F(MHz) in total length, where F (MHz) is the lowest frequency to be used. For 3.5MHz this equates to 288 foot perimeter (square, delta, multi-side ok).
Production Note: These hybrid baluns are special order and made to order for each customer. Please note that shipping will be approximately 2-3 weeks after order placed depending upon our existing production schedule.
Pictures show 2-1 balun but you will receive the 2.25:1 balun with 1:1 hybrid in a single enclosure.
