5:1 CUBE™ Unun – Model CU-5-1500 (50:250 Ohm, 1.8-61 MHz, 1.5KW PEP)
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 unun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical application:
Also available as a balanced output – CB-5-1500
CB Radio Generic Mobile Transceiver RFI/Noise Reduction Kit, RFI Range: 20-60 MHz, Works on all brandsProduct DetailsMPN: RFI-CB-MOBILECountry/Region of Manufacture: United StatesFilter Power Rating (PEP watts): 500Common Mode Attenuation (db): <=25 dBRFI Suppression Range (MHz): 20-60 MHz# Ferrite Filters: 2Palomar Engineers RFI Filter Kit for CB Radio Radio Transceivers from 20-30 MHz uses ferrite rings for the DC power supply and the coax to the antenna.
BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH ALL BRANDS (Cobra, DAS, Midland, Uniden etc.) OF CB/HAM/COMMERCIAL RADIO RIGS in 20-60 MHz range.
Purpose
The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and on the DC power supply cable.
This kit will help reduce or eliminate:
1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.
2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.
3. RFI to your other radios, audio/video systems, computers, telephones, etc.
A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).
These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from Ham Radio amplifiers.
Included are the following chokes and installation guidelines:
DC Input: F240 Ring – 3-7 turns of DC power cable - sized for smaller plugs
RF Input/Output: F240-31 ring - wrap 6 turns of RG8X size cable near the back of the radio
Also make sure you connect a good RF ground to the transceiver ground post.
For additional RFI suppression, use a MC-1-500-50 mini feed line choke at the antenna feed point to suppress common current on the coax feed line during transmit and a CMNF-500-50 Coax Noise Filter to reduce common mode noise during receive operations.
If you use a switching power supply for base operation, consider the RFI-SMPS switching power supply RFI kit.
If you use a linear amplifier we have RFI kits for linear amplifiers that help suppress RFI in your shack or in your neighbor’s house.
Palomar Engineers RFI Filter Kit for CB Radio Radio Transceivers from 20-30 MHz uses ferrite rings for the DC power supply and the coax to the antenna.
BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH ALL BRANDS (Cobra, DAS, Midland, Uniden etc.) OF CB/HAM/COMMERCIAL RADIO RIGS in 20-60 MHz range.
Purpose
The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and on the DC power supply cable.
This kit will help reduce or eliminate:
1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.
2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.
3. RFI to your other radios, audio/video systems, computers, telephones, etc.
A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).
These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from Ham Radio amplifiers.
Included are the following chokes and installation guidelines:
DC Input: F240 Ring – 3-7 turns of DC power cable - sized for smaller plugs
RF Input/Output: F240-31 ring - wrap 6 turns of RG8X size cable near the back of the radio
For additional RFI suppression, use a MC-1-500-50 mini feed line choke at the antenna feed point to suppress common current on the coax feed line during transmit and a CMNF-500-50 Coax Noise Filter to reduce common mode noise during receive operations.
If you use a switching power supply for base operation, consider the RFI-SMPS switching power supply RFI kit.
If you use a linear amplifier we have RFI kits for linear amplifiers that help suppress RFI in your shack or in your neighbor’s house.
