5:1 CUBE™ Unun – Model CU-5-1500 (50:250 Ohm, 1.8-61 MHz, 1.5KW PEP)
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 unun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical application:
Also available as a balanced output – CB-5-1500
ACOM 2000 HF Linear Amplifier + Remote Control Unit RFI Kit - 8 RFI/Noise Reduction FiltersProduct DetailsMPN: RFI-LA-AC2000Filter Power Rating (PEP watts): coax cable limitRFI Suppression Range (MHz): 1-60 MHz# Ferrite Filters: 8PURPOSE
These kits are designed to choke common mode currents going into or exiting from your amplifier cables.Filters are supplied for the RF In, RF Out, Relay Cable/control lines, remote control unit and AC power line.Use of the filters often helps cure SWR problems between amp exciter and amp and between amp and antenna tuner or direct to antenna.The AC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.
USE
KIT INCLUDES
Filter Type
Usage
Ferrites
F240 Ring (1.4” ID)
Transceiver RF coaxr
1
Snap On (1/2” ID)
Remote Control Unit cables
5
Snap On (1” ID)
RF Output, AC/DC power
2
Total Filters
8
INSTALLATION GUIDELINES
Amp RF Input:Ring Filter (1.4” ID) – 5-9 turns of RG-58/8X size through center
Amp RF Output:Snap On Filter (1” ID) – 3 turns of coax cable through center
RCU Cables:Snap On Filter (1/2” ID) – multiple turns through center
AC Power:Snap On Filter (1” ID) – 3 turns of power cord through center
On Sale
RG-8X Coax Jumper Cable with PL-259's on each end - 3 feetRG-8X Coax Jumper Cable with PL-259's on each end - 3 feetSKU RG-8X-3List price $19.95 Save 15%$16.95
PURPOSE
These kits are designed to choke common mode currents going into or exiting from your amplifier cables.Filters are supplied for the RF In, RF Out, Relay Cable/control lines, remote control unit and AC power line.Use of the filters often helps cure SWR problems between amp exciter and amp and between amp and antenna tuner or direct to antenna.The AC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.
USE
KIT INCLUDES
|
Filter Type |
Usage |
Ferrites |
|
F240 Ring (1.4” ID) |
Transceiver RF coaxr |
1 |
|
Snap On (1/2” ID) |
Remote Control Unit cables |
5 |
|
Snap On (1” ID) |
RF Output, AC/DC power |
2 |
|
Total Filters |
8 |
INSTALLATION GUIDELINES
Amp RF Input:Ring Filter (1.4” ID) – 5-9 turns of RG-58/8X size through center
Amp RF Output:Snap On Filter (1” ID) – 3 turns of coax cable through center
RCU Cables:Snap On Filter (1/2” ID) – multiple turns through center
AC Power:Snap On Filter (1” ID) – 3 turns of power cord through center
