Snap On Split Beads

Chameleon Antenna Tuner CHA URT1, 1.8-54 MHz, 16K memories, 125W SSB, POTA, SOTA

SKU CHA URT1
$399.00
NEW PRODUCT
1
Save this product for later
Customer reviews
Reviews only from verified customers
No reviews yet. You can buy this product and be the first to leave a review.
Share this product with your friends
Chameleon Antenna Tuner CHA URT1, 1.8-54 MHz, 16K memories, 125W SSB, POTA, SOTA
Product Details

CHA URT1 (Universal Remote Tuner 1)

_________________________________

The CHA URT1 is a remote outdoor tuner for almost any type of antenna and any brand or model transceiver. The CHA URT1 is unique in that it can be used for coaxial cable or wire fed antennas. This wide-range tuner will match wire antennas, such as a vertical, random wire antenna, or a long wire antenna. It can also be used with coaxial-fed antennas, like an Inverted “V” or dipole. Also, the CHA URT1 does not need a transceiver-specific control cable, so it works with any brand or model of transceiver. The rugged Tuner Unit is weatherproof and designed to be permanently installed outdoors at or near the antenna feed point, so loss due to high SWR on the feedline is avoided.

The CHA URT1 covers 1.8 – 54.0 MHz and has 16,000 memories for quick recall and tuning with previously used settings. It can match any antenna with an impedance of 5 to 1,500 Ohms within seconds and can handle up to 125W SSB Phone & CW, 100W SSB Phone & CW on 50 MHz, 60W all other modes (see specifications). The CHA URT1 consists of two units: a Coupler Unit and the Tuner Unit. The Tuner Unit is in a rugged weatherproof housing and contains the antenna matching network and controller. It is normally installed outside at or near the antenna feed point. The Coupler Unit contains the operator controls and status indicators. It uses a bias-T circuit to send power and control signals to the remote Tuner Unit over the connecting coaxial cable, so there is no need to order or install a separate transceiver-specific control cable. The Coupler Unit is not weatherproof and must be installed inside near the operator and transceiver.

IF YOU'RE INSTALLING A LIGHTNING ARRESTOR INLINE WITH THE CHA URT1 YOU'VE TO USE: Morgan RF Systems M-303U-PP coaxial arrestor

Our tuners use latching relays. Once the tuner is tuned the relay's latch and power is turned off. It saves on battery drain. The tuned frequency will be stored in memory. When you change frequency or bands you need to apply power and energize the tuning process again. If the frequency is in memory the tuning process will be quick!

WE RECOMMEND TO INSTALL A RFI CHOKE SUCH AS THE MC-1-500 AT THE FEED POINT OF THE TUNER.

Consist of:

1 X Universal Remote Tuner 1

1 X Coupler Unit

1 X 12V Hardwire Power Cord

2 X U-Bolt Attachment Brackets and Hardware

2 X U-Bolt(1/4" x 1-3/4" x 3")



Specifications

  • Frequency Range: 1.8 to 54.0 MHz
  • Power Handling:
  • HF: 125W SSB/CW
  • 6M: 100W SSB/CW
  • All other modes: 60W
  • Tuning Power Range: 0.5 - 15W
  • Tuning Time: 5 seconds for full tune: 0.1 Second for memory tune.
  • Memory: 16,000 frequencies
  • Power Supply: 12-14 DC, 1A
  • Temperature Range: Approximately 14°F (-10°C) to 140°F (60°C)
  • Turner Unit Dimensions: 8.8 X 5.1 X 1.8 inches (223mm X 130mm X 45mm)
  • Tuner Unit Weight: 38.8 oz (1100g)
  • Coupler Unit Dimensions: 5.0 X 4.1 X 7 inches (128mm X 105mm X 43mm)
  • Coupler Unit Weight: 14.1 oz (400g)
  • Current consumption: 500mA or less
  • Magnetic latching relay. Once the tuner is tuned the relay's latch and power is turned off. It saves on battery drain. The tuned frequency will be stored in memory. When you change frequency or bands you need to apply power and energize the tuning process again. If the frequency is in memory the tuning process will be quick !

Optional:

1 X 12V power supply

1 X 3ft of 50 Ohm stranded center conductor RG-8X with PL-259 Connectors

Often it is difficult to slip beads on a cable because of a plug or connector. Split beads solve this problem. They come in two halves that fit over the cable. A plastic snap cover holds the two halves together and holds the assembly on the cable.

For RFI use, mix 31 is effective from 1-300 Mhz, mix 43 works from 20-250 Mhz, Mix 61 is for 200-2000 Mhz, and mix 77 favors .1-20 MHz. These frequencies are those of the interfering signal to be eliminated, not the operating frequencies of the equipment to be protected.

Not sure of what sizes you need or solving a RFI problem with devices using multiple size cables?  Try the Ferrite Snap On Combo Pack which has sizes from 1/4″ to 3/4″ with either Mix 31 (1-300 MHz) or Mix 61 (200-2000 MHz) or Mix 75 (150 KHz – 10 MHz).

 NOW WITH QUANTITY PRICING FOR CLUB , VOLUME PURCHASERS!

Bead dimensions are shown in the picture below and in the table as A, B, C

FAIR RITE 185M CLIP ON FERRITE BEAD SPLIT CORE - Snap On Split Beads

Ferrite Split Bead Dimensions

Application Notes

Application Note for using these Snap On split beads: How Many Chokes do I need?

You can very effectively increase the choking impedance of smaller cable by using a large hole ferrite bead and wrapping the cable through several times.  For particularly difficult common mode current/RFI problems you may need a choking impedance as high as 5-10K ohms.  Using multiple beads and multiple turns through each bead will give higher impedances up to a point.  At higher frequencies, when the number of turns approaches an electrical wavelength, the choke becomes resonant due to stray capacitance and the inductance of the cable and limits the high end impedance values to less than the above table points.

Some example of ways to wrap cable are shown below.

Ferrite Split Beads with multiple turns of RG-58/59

FSB14 1 150x150 - Snap On Split Beads

FSB-1/4 – 1 turn

FSB 12 1 150x150 - Snap On Split Beads

FSB-1/2 1 turn

FSB12 1 Open 150x150 - Snap On Split Beads

FSB-1/2 Open Shell

FSB 12 2 150x150 - Snap On Split Beads

FSB-1/2 2 turns

FSB 12 3 150x150 - Snap On Split Beads

FSB-1/2 3 turns

FSB12 4 150x150 - Snap On Split Beads

FSB-1/2 4 turns

—–//—–

More examples of split bead use

20131210 1148191 300x180 - Snap On Split Beads

Ethernet Cable on FSB-1/4

20131210 114800 300x180 - Snap On Split Beads

Ethernet Cable on FSB-1/2 – 3 turns for 9X Impedance good filter for 15-30 mhz between 2K-3K ohms choking Z

Three Effective Radio Interference Filters

Effective RFI/EMI Chokes

20131219 110956 150x150 - Snap On Split Beads

FSB-1/4 or FSB-1/2 4 turns for 14-50 Mhz 2K-3K Z

20131219 111243 150x150 - Snap On Split Beads

FSB-1/2-5 turns for 10-30 Mhz 2K-4.5K choking Z

20131219 105947 150x150 - Snap On Split Beads

FT240-43 – 14 turns for 3-14 Mhz or use two FT240-43 for 1.8-10 Mhz

These snap-on chokes are useful for reducing RFI in public address system amplifiers, speaker wires, mic cables, mixer panels, coax cable, telephone wires, computer sound card speakers, dsl/cable connections, remote control heads for ham transceivers (Especially FT-100, FT900, IC-706, IC-7000), AC power cables, DC power cables, home theater cables, video cables, HI Fi cables, guitar amps, linear amp cables, etc.

 

They are also helpful in suppressing common mode noise/RFI in radio and TV receivers, audio and RF amplifiers.  They can also help suppress noise generated by treadmills, exercise equipment, fish tank heaters, oil heater pumps, fluorescent lights, motors, cable modems, DSL modems, computers, and many other electrical devices.  Common mode current reduction in computer cables often helps speed up computers.