Purpose. The CU-4-1500 is used as a 4:1 (200 ohm unbalanced load to 50 ohm unbalanced source) broadband transformer for 50 ohm coax cable rated at at 1500 PEP into 200 ohms unbalanced load from 1.8-61 MHz. Excellent for 31-33, 41 and 43 foot multi-band verticals and also slopers (51', 85' or 119" work great) made by S9, ZeroFive, MFJ and DX Engineering and Palomar Engineers vertical antennas
USE: The top connector is for the 200 ohm unbalanced output, and the side connector is for a ground rod, counterpoise or radial connection.The SO-239 input connector shield/ground is shared with the ground connector.
For best results use a feed line choke between the CU-4-1500 and the coax input to isolate the coax from becoming part of the antenna. Our Maxi-Choker (MC-1-3000) is an excellent companion for this unun.
This Unun is a very efficient match for many 43 and 31-33 foot multi-band verticals including the S9, ZeroFive, MFJ and DX Engineering vertical antennas.
The CU-4-1500 is also useful for end fed OCF antennas utilizing a 4:1 unun and a coax feed line choke to set the antenna length for the "short" side of the OCF.
CU-4-5000 is in a 4" x 4" x 2" NEMA enclosure and weighs 3 pounds and is specified for 1.8-31 MHz - rated at 5KW PEP
CU-4-5000HD is in a 4" x 4" x 4" NEMA enclosure, contains 50% more ferrite cores then the 5000 and weighs 4 pounds and is specified for 1.8-31 MHz - rated at 4KW continuous duty, 5K+ PEP. The HD version of this unun is CUSTOM MADE PER ORDER - PLEASE ALLOW 2 WEEKS FOR MANUFACTURING PRIOR TO SHIPMENT.
Often it is difficult to slip beads on a cable because of a plug or connector. Split beads solve this problem. They come in two halves that fit over the cable. A plastic snap cover holds the two halves together and holds the assembly on the cable.
For RFI use, mix 31 is effective from 1-300 Mhz, mix 43 works from 20-250 Mhz, Mix 61 is for 200-2000 Mhz, and mix 77 favors .1-20 MHz. These frequencies are those of the interfering signal to be eliminated, not the operating frequencies of the equipment to be protected.
Not sure of what sizes you need or solving a RFI problem with devices using multiple size cables? Try the Ferrite Snap On Combo Pack which has sizes from 1/4″ to 3/4″ with either Mix 31 (1-300 MHz) or Mix 61 (200-2000 MHz) or Mix 75 (150 KHz – 10 MHz).
NOW WITH QUANTITY PRICING FOR CLUB , VOLUME PURCHASERS!
Bead dimensions are shown in the picture below and in the table as A, B, C
Ferrite Split Bead Dimensions
Application Notes
Application Note for using these Snap On split beads: How Many Chokes do I need?
You can very effectively increase the choking impedance of smaller cable by using a large hole ferrite bead and wrapping the cable through several times. For particularly difficult common mode current/RFI problems you may need a choking impedance as high as 5-10K ohms. Using multiple beads and multiple turns through each bead will give higher impedances up to a point. At higher frequencies, when the number of turns approaches an electrical wavelength, the choke becomes resonant due to stray capacitance and the inductance of the cable and limits the high end impedance values to less than the above table points.
Some example of ways to wrap cable are shown below.
 FSB-1/4 – 1 turn |
 FSB-1/2 1 turn |
 FSB-1/2 Open Shell |
 FSB-1/2 2 turns |
 FSB-1/2 3 turns |
 FSB-1/2 4 turns |
—–//—–
More examples of split bead use
Ethernet Cable on FSB-1/4
Ethernet Cable on FSB-1/2 – 3 turns for 9X Impedance good filter for 15-30 mhz between 2K-3K ohms choking Z
Three Effective Radio Interference Filters
 FSB-1/4 or FSB-1/2 4 turns for 14-50 Mhz 2K-3K Z |
 FSB-1/2-5 turns for 10-30 Mhz 2K-4.5K choking Z |
 FT240-43 – 14 turns for 3-14 Mhz or use two FT240-43 for 1.8-10 Mhz |
These snap-on chokes are useful for reducing RFI in public address system amplifiers, speaker wires, mic cables, mixer panels, coax cable, telephone wires, computer sound card speakers, dsl/cable connections, remote control heads for ham transceivers (Especially FT-100, FT900, IC-706, IC-7000), AC power cables, DC power cables, home theater cables, video cables, HI Fi cables, guitar amps, linear amp cables, etc.
They are also helpful in suppressing common mode noise/RFI in radio and TV receivers, audio and RF amplifiers. They can also help suppress noise generated by treadmills, exercise equipment, fish tank heaters, oil heater pumps, fluorescent lights, motors, cable modems, DSL modems, computers, and many other electrical devices. Common mode current reduction in computer cables often helps speed up computers.