Model BA-1-1000 is a 1:1 balun kit used to translate a 50 ohm
unbalanced input to 50 ohms unbalanced at power levels up to 1000 watts
PEP/100 watts continuous when used with a matched load. With a matched
load the SWR will not exceed 1.5 over the frequency range 1.8 to 61 MHz.
1,000 PEP watt rating on a 25% duty cycle. Will sustain about 100 watts RTTY or FT8 at 6 meters. (for higher power use the BA-1-1500 with 6-8 turns for higher frequencies).
Common mode impedance peaks
around 3,500 ohms at 10Mmhz.
With a matched 50 ohm load the SWR over the frequency range 1.8 to 61
MHz is shown in the following table measured with an AIM 4170 network
analyzer. Notice that the conversion from 50 to 50 ohms is very
consistent from 1.8-61 MHz and SWR is less than 1.3:1 over the range
allowing easy tuning by most radio internal antenna tuners or an
external tuner.
Ba-1-1000 1:1 Balun/Unun 1KW PEP 1-61 Mhz
The kit consists of a F140 ferrite toroidal core, enamel insulated
wire, a SO-239 connector with stainless steel hardware, and an
illustrated instruction manual with directions to connect the kit as a 1
to 1 balun/unun (unbalanced coax to unbalanced antenna or balanced
antenna like a dipole). Balun assembly time takes about an hour and is a
fun learning process.
Add a SO-239 Kit on output side to create a 1:1 unun (coax to coax line isolator) or add studs for a balun for use with dipole or beam antenna.
Use the recommwnded CB-Box-1 for a convenient enclosure.
Often it is difficult to slip beads on a cable because of a plug or connector. Split beads solve this problem. They come in two halves that fit over the cable. A plastic snap cover holds the two halves together and holds the assembly on the cable.
For RFI use, mix 31 is effective from 1-300 Mhz, mix 43 works from 20-250 Mhz, Mix 61 is for 200-2000 Mhz, and mix 77 favors .1-20 MHz. These frequencies are those of the interfering signal to be eliminated, not the operating frequencies of the equipment to be protected.
Not sure of what sizes you need or solving a RFI problem with devices using multiple size cables? Try the Ferrite Snap On Combo Pack which has sizes from 1/4″ to 3/4″ with either Mix 31 (1-300 MHz) or Mix 61 (200-2000 MHz) or Mix 75 (150 KHz – 10 MHz).
NOW WITH QUANTITY PRICING FOR CLUB , VOLUME PURCHASERS!
Bead dimensions are shown in the picture below and in the table as A, B, C
Ferrite Split Bead Dimensions
Application Notes
Application Note for using these Snap On split beads: How Many Chokes do I need?
You can very effectively increase the choking impedance of smaller cable by using a large hole ferrite bead and wrapping the cable through several times. For particularly difficult common mode current/RFI problems you may need a choking impedance as high as 5-10K ohms. Using multiple beads and multiple turns through each bead will give higher impedances up to a point. At higher frequencies, when the number of turns approaches an electrical wavelength, the choke becomes resonant due to stray capacitance and the inductance of the cable and limits the high end impedance values to less than the above table points.
Some example of ways to wrap cable are shown below.
 FSB-1/4 – 1 turn |
 FSB-1/2 1 turn |
 FSB-1/2 Open Shell |
 FSB-1/2 2 turns |
 FSB-1/2 3 turns |
 FSB-1/2 4 turns |
—–//—–
More examples of split bead use
Ethernet Cable on FSB-1/4
Ethernet Cable on FSB-1/2 – 3 turns for 9X Impedance good filter for 15-30 mhz between 2K-3K ohms choking Z
Three Effective Radio Interference Filters
 FSB-1/4 or FSB-1/2 4 turns for 14-50 Mhz 2K-3K Z |
 FSB-1/2-5 turns for 10-30 Mhz 2K-4.5K choking Z |
 FT240-43 – 14 turns for 3-14 Mhz or use two FT240-43 for 1.8-10 Mhz |
These snap-on chokes are useful for reducing RFI in public address system amplifiers, speaker wires, mic cables, mixer panels, coax cable, telephone wires, computer sound card speakers, dsl/cable connections, remote control heads for ham transceivers (Especially FT-100, FT900, IC-706, IC-7000), AC power cables, DC power cables, home theater cables, video cables, HI Fi cables, guitar amps, linear amp cables, etc.
They are also helpful in suppressing common mode noise/RFI in radio and TV receivers, audio and RF amplifiers. They can also help suppress noise generated by treadmills, exercise equipment, fish tank heaters, oil heater pumps, fluorescent lights, motors, cable modems, DSL modems, computers, and many other electrical devices. Common mode current reduction in computer cables often helps speed up computers.