For best results support center at 30+ feet and ends over 15 feet. Angle of feed each side must be great than 45 degrees or 120 – 180 degrees total between each side preferred. Any length of 50 ohm feed line ok (from the matching unit) but longer feed lines over 50 feet may show reduced SWR on some bands due to losses in feed line and soil conductivity, nearby objects, etc. Due to local ground conditions, antenna height and feed line length, SWR may vary from samples shown and an antenna tuner may be required or some bands to bring SWR at end of feed line to acceptable levels. Antenna Length Note:These antennas are shipped from the factory with each side at 46 feet long (92 feet total) so that you may adjust(shorten) the length for your personal installation.The SWR graph shown for this product is for a side length of 44 feet as this length provides a lower SWR in the 17 meter band than the 46 foot length. The longer 46 foot length tends to shift the SWR curves to the left (lower frequency) which can sometimes be offset by reducing the length of the ladder line (up to 2 feet max). Each antenna installation is unique – try the antenna lengths as received and shorten the wire length by bending back the wires on themselves at the ends as needed. Use an antenna tuner for 80, 30, 15 meters and reduce power if balun saturation occurs. FREE USA Shipping on orders over $100 Insulators may be black, grey or white depending on stock at hand when order is placed. Wire is stranded, AWG#14, insulated and black or grey color.
Excellent features:
*** Covers 40-20-17-12-10 meter ham bands under 2:1 at most heights no tuner required, 80, 15, 6 meter bands require wide range tuner
*** Great digital/FT8 antenna on many bands without tuner
*** Low SWR on many bands or use antenna tuner
*** 500 watts/1.5KW/5KW PEP (SSB-ICAS) options
*** Stainless Steel hardware for long life
*** Halyard Hoist hole for ease of center support installation or hang at ends only
*** Insulated #14 wire for durability
*** High Strength insulators (may be black, white or gray)
*** Ladder Line to 1:1 Balun (Note 1500/5000 Watts CUBE Balun can be mounted to a wall, 500 watts MB-1-500 is supported by ladder line
Super convenient and quick – great for contest operation! Choose 500, 1500 or 5000 watt PEP (use 5KW model for digital modes over 1000 watts).
INSTALLATION
For RFI common mode suppression use, mix 31 is effective from 1-300 Mhz, mix 43 works from 25-300 Mhz, Mix 61 is for 200-2000 Mhz, and mix 77 favors .1-50 MHz. These frequencies are those of the interfering signal to be eliminated, not the operating frequencies of the equipment to be protected. See Mix Selection for other applications.
NOW WITH QUANTITY PRICING FOR CLUB , VOLUME PURCHASERS!
Bead dimensions are shown in the picture below and in the table as A, B, C
Ferrite Bead Dimensions
Application Note: Use impedances for each bead at your desired frequency to select number of beads needed for desired Z. For example if you have a 50 ohm RG-8 coax cable and want a choking impedance of 500 ohms at 10 Mhz, you can check the FB102 column (since FB102 will pass RG-8 through its center ID) at 10Mhz and find that Mix 31 has a Z of 108 ohms/bead and Mix 43 has a Z of 91 ohms/bead. For 500 ohms we would need 5 mix 31 beads or 6 mix 43 beads to have greater than 500 ohms. Mix 31 has better response below 10 Mhz but above 10 Mhz mix 31 and mix 43 are very close. If you need more Z, just use more beads in series on the cable or use more windings thru a larger ID bead (e.g. USE FB102-31 for 4 turns of RG-8X for 16X increase in Z per bead – see pictures below for examples). Use Mix 61 for VHF and above for RFI/EMI suppression and below 30 Mhz for multi-ratio impedance transformers (baluns/ununs). See Mix Selection for other applications.
For extra large cables use the FB400-31 which has an inside diameter of 3 inches (76mm).
Frequency Range Comparison Chart
(FB56-xx size)
Multi-turn Common Mode Choking Impedance Increase Example (FB56-43)
Ferrite Bead relative size comparison
Left to right sizes: FB56 (ID = .25″), FB102 (ID=.505″), FB103 (ID=.77″)
SLIP ON Sizes for Heliax and Coax Cable
Cascaded Common Mode Chokes/Line Isolators/1:1 Baluns
 RG58 4 turns on 2 FB102-31 for 2000 ohms choking impedance |
 RG58 12 turns on FT240-43 for 4000-6000 ohms choking impedance |
Handy Wire Size reference for ferrite bead sizes needed
————————————————–/———————————————————
Connector already on cable? See Snap On Ferrite Beads for convenient installation on cables with connector already installed.