New improved version now goes down to 500 KHz (25 dB common mode AM Broadcast band suppression) and up to 61 MHz < 2:1 SWR. Choose Balun only or add optional dipole wire kit (wire, Insulators, Spade lugs for attachment to balun - assembly required). Center insulator and Balun in one case - 1/4" stainless hardware and 1500 real watts rated! The SBullet-1B-1500EB is a multi-core current balun with built in feed line choke offering up to 38 dB (on 20 meters) of common mode current rejection (plenty for most applications) to keep RFI off the coax outer braid during transmit operations. The SBullet-1B-1500EB is housed in a waterproof PVC enclosure that is lightweight yet robust in features and makes a great high power antenna feed solution for dipoles and other balanced antennas. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 coax connector and output with dual side eye bolt output and wire strain relief. Rated 1500 Watts PEP Watts from .1-61 MHz. SBullet-1B-1500EB weight is 2 pounds. This balun/feedline choke keeps TRANSMIT RFI off the coax outer braid while transmitting. If your station suffers from common mode RFI noise on RECEIVE, then use one of our Common Mode Coax Noise Filters (such as the CMNF-1500) that suppresses common mode noise on RECEIVE operations. Make a FAN DIPOLE using optional dipole kits (e.g. 80/40 would use extra 40 meter dipole if you chose the 80 meter dipole lit for this listing).
NOTE: We rate our Bullet baluns (and ununs) VERY conservatively at 1500 watts PEP with a 50% duty cycle. Some manufacturers selling low cost baluns may use a 5% duty cycle for their PEP rating to make it appear you get a higher rated balun for a lower price, but you may in fact be getting be getting less. Their 1500 watts PEP really means 75 watts continuous or 150 watts at a 50% duty cycle (like FT8) compared to our 1000 watts at 50% duty cycle (assuming a SWR < 2:1). Our baluns typically cover a larger frequency range under 2:1 SWR which make your transceiver happy and probably will last longer with less electrical stress. Remember we over engineer our products, to out perform our competition - just compare the weight of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.
For RFI common mode suppression use, mix 31 is effective from 1-300 Mhz, mix 43 works from 25-300 Mhz, Mix 61 is for 200-2000 Mhz, and mix 77 favors .1-50 MHz. These frequencies are those of the interfering signal to be eliminated, not the operating frequencies of the equipment to be protected. See Mix Selection for other applications.
NOW WITH QUANTITY PRICING FOR CLUB , VOLUME PURCHASERS!
Bead dimensions are shown in the picture below and in the table as A, B, C
Ferrite Bead Dimensions
Application Note: Use impedances for each bead at your desired frequency to select number of beads needed for desired Z. For example if you have a 50 ohm RG-8 coax cable and want a choking impedance of 500 ohms at 10 Mhz, you can check the FB102 column (since FB102 will pass RG-8 through its center ID) at 10Mhz and find that Mix 31 has a Z of 108 ohms/bead and Mix 43 has a Z of 91 ohms/bead. For 500 ohms we would need 5 mix 31 beads or 6 mix 43 beads to have greater than 500 ohms. Mix 31 has better response below 10 Mhz but above 10 Mhz mix 31 and mix 43 are very close. If you need more Z, just use more beads in series on the cable or use more windings thru a larger ID bead (e.g. USE FB102-31 for 4 turns of RG-8X for 16X increase in Z per bead – see pictures below for examples). Use Mix 61 for VHF and above for RFI/EMI suppression and below 30 Mhz for multi-ratio impedance transformers (baluns/ununs). See Mix Selection for other applications.
For extra large cables use the FB400-31 which has an inside diameter of 3 inches (76mm).
Frequency Range Comparison Chart
(FB56-xx size)
Multi-turn Common Mode Choking Impedance Increase Example (FB56-43)
Ferrite Bead relative size comparison
Left to right sizes: FB56 (ID = .25″), FB102 (ID=.505″), FB103 (ID=.77″)
SLIP ON Sizes for Heliax and Coax Cable
Cascaded Common Mode Chokes/Line Isolators/1:1 Baluns
 RG58 4 turns on 2 FB102-31 for 2000 ohms choking impedance |
 RG58 12 turns on FT240-43 for 4000-6000 ohms choking impedance |
Handy Wire Size reference for ferrite bead sizes needed
————————————————–/———————————————————
Connector already on cable? See Snap On Ferrite Beads for convenient installation on cables with connector already installed.