The Ferrite Snap On Combo Pack is a convenient solution for troubleshooting RFI/EMI with various diameter cables ranging from 1/4″ to 3/4″ for use as either single turn or multiple turn ferrite chokes. The snap on chokes are useful for RF coax, AC/DC power cables, and device interconnection cables. Always use a snap on with a larger inside diameter than the diameter of the cable and use multiple turns if possible (2 turns through the snap on is the same as 4 snap ons with 1 turns). Included in these combo packs are our most popular snap on sizes as follows: FSB75-1/4 – 1/4″ ID – 4 pieces FSB75-1/2 – 1/2″ ID – 2 pieces FSB75-3/4 – 3/4″ ID – 2 pieces Normal Retail price is $140 for these parts individually - this items qualifies your USA order for free shipping. Excellent for AC/DC power cables on switching power supplies, variable speed motor controllers, and data/audio/video cables for AM broadcast RFI suppression.
Mix 75 Ferrite Snap On Combo 8 pack (RFI Suppression range is 150 KHz – 10 MHz)
For RFI common mode suppression use, mix 31 is effective from 1-300 Mhz, mix 43 works from 25-300 Mhz, Mix 61 is for 200-2000 Mhz, and mix 77 favors .1-50 MHz. These frequencies are those of the interfering signal to be eliminated, not the operating frequencies of the equipment to be protected. See Mix Selection for other applications.
NOW WITH QUANTITY PRICING FOR CLUB , VOLUME PURCHASERS!
Bead dimensions are shown in the picture below and in the table as A, B, C
Ferrite Bead Dimensions
Application Note: Use impedances for each bead at your desired frequency to select number of beads needed for desired Z. For example if you have a 50 ohm RG-8 coax cable and want a choking impedance of 500 ohms at 10 Mhz, you can check the FB102 column (since FB102 will pass RG-8 through its center ID) at 10Mhz and find that Mix 31 has a Z of 108 ohms/bead and Mix 43 has a Z of 91 ohms/bead. For 500 ohms we would need 5 mix 31 beads or 6 mix 43 beads to have greater than 500 ohms. Mix 31 has better response below 10 Mhz but above 10 Mhz mix 31 and mix 43 are very close. If you need more Z, just use more beads in series on the cable or use more windings thru a larger ID bead (e.g. USE FB102-31 for 4 turns of RG-8X for 16X increase in Z per bead – see pictures below for examples). Use Mix 61 for VHF and above for RFI/EMI suppression and below 30 Mhz for multi-ratio impedance transformers (baluns/ununs). See Mix Selection for other applications.
For extra large cables use the FB400-31 which has an inside diameter of 3 inches (76mm).
Frequency Range Comparison Chart
(FB56-xx size)
Multi-turn Common Mode Choking Impedance Increase Example (FB56-43)
Ferrite Bead relative size comparison
Left to right sizes: FB56 (ID = .25″), FB102 (ID=.505″), FB103 (ID=.77″)
SLIP ON Sizes for Heliax and Coax Cable
Cascaded Common Mode Chokes/Line Isolators/1:1 Baluns
 RG58 4 turns on 2 FB102-31 for 2000 ohms choking impedance |
 RG58 12 turns on FT240-43 for 4000-6000 ohms choking impedance |
Handy Wire Size reference for ferrite bead sizes needed
————————————————–/———————————————————
Connector already on cable? See Snap On Ferrite Beads for convenient installation on cables with connector already installed.