Purpose. The CU-4-1500 is used as a 4:1 (200 ohm unbalanced load to 50 ohm unbalanced source) broadband transformer for 50 ohm coax cable rated at at 1500 PEP into 200 ohms unbalanced load from 1.8-61 MHz. Excellent for 31-33, 41 and 43 foot multi-band verticals and also slopers (51', 85' or 119" work great) made by S9, ZeroFive, MFJ and DX Engineering and Palomar Engineers vertical antennas USE: The top connector is for the 200 ohm unbalanced output, and the side connector is for a ground rod, counterpoise or radial connection.The SO-239 input connector shield/ground is shared with the ground connector. For best results use a feed line choke between the CU-4-1500 and the coax input to isolate the coax from becoming part of the antenna. Our Maxi-Choker (MC-1-3000) is an excellent companion for this unun. This Unun is a very efficient match for many 43 and 31-33 foot multi-band verticals including the S9, ZeroFive, MFJ and DX Engineering vertical antennas. The CU-4-1500 is also useful for end fed OCF antennas utilizing a 4:1 unun and a coax feed line choke to set the antenna length for the "short" side of the OCF. CU-4-5000 is in a 4" x 4" x 2" NEMA enclosure and weighs 3 pounds and is specified for 1.8-31 MHz - rated at 5KW PEP CU-4-5000HD is in a 4" x 4" x 4" NEMA enclosure, contains 50% more ferrite cores then the 5000 and weighs 4 pounds and is specified for 1.8-31 MHz - rated at 4KW continuous duty, 5K+ PEP. The HD version of this unun is CUSTOM MADE PER ORDER - PLEASE ALLOW 2 WEEKS FOR MANUFACTURING PRIOR TO SHIPMENT.
For RFI common mode suppression use, mix 31 is effective from 1-300 Mhz, mix 43 works from 25-300 Mhz, Mix 61 is for 200-2000 Mhz, and mix 77 favors .1-50 MHz. These frequencies are those of the interfering signal to be eliminated, not the operating frequencies of the equipment to be protected. See Mix Selection for other applications.
NOW WITH QUANTITY PRICING FOR CLUB , VOLUME PURCHASERS!
Bead dimensions are shown in the picture below and in the table as A, B, C
Ferrite Bead Dimensions
Application Note: Use impedances for each bead at your desired frequency to select number of beads needed for desired Z. For example if you have a 50 ohm RG-8 coax cable and want a choking impedance of 500 ohms at 10 Mhz, you can check the FB102 column (since FB102 will pass RG-8 through its center ID) at 10Mhz and find that Mix 31 has a Z of 108 ohms/bead and Mix 43 has a Z of 91 ohms/bead. For 500 ohms we would need 5 mix 31 beads or 6 mix 43 beads to have greater than 500 ohms. Mix 31 has better response below 10 Mhz but above 10 Mhz mix 31 and mix 43 are very close. If you need more Z, just use more beads in series on the cable or use more windings thru a larger ID bead (e.g. USE FB102-31 for 4 turns of RG-8X for 16X increase in Z per bead – see pictures below for examples). Use Mix 61 for VHF and above for RFI/EMI suppression and below 30 Mhz for multi-ratio impedance transformers (baluns/ununs). See Mix Selection for other applications.
For extra large cables use the FB400-31 which has an inside diameter of 3 inches (76mm).
Frequency Range Comparison Chart
(FB56-xx size)
Multi-turn Common Mode Choking Impedance Increase Example (FB56-43)
Ferrite Bead relative size comparison
Left to right sizes: FB56 (ID = .25″), FB102 (ID=.505″), FB103 (ID=.77″)
SLIP ON Sizes for Heliax and Coax Cable
Cascaded Common Mode Chokes/Line Isolators/1:1 Baluns
 RG58 4 turns on 2 FB102-31 for 2000 ohms choking impedance |
 RG58 12 turns on FT240-43 for 4000-6000 ohms choking impedance |
Handy Wire Size reference for ferrite bead sizes needed
————————————————–/———————————————————
Connector already on cable? See Snap On Ferrite Beads for convenient installation on cables with connector already installed.