Impedance Transformers (<1:1, >1:1)

50:200 (4:1) CUBE™ Current Balun, 1.8-61 MHz, 1.5KW - Loop, OCF, Folded Dipole useful to 200 MHz

SKU CB-4-1500EB
$124.95
Bulk pricing available for quantities of 2 units or more
Select Output Connector
1
Buy more, save more
QuantityPrice per itemDiscount
2 items$116.956% off
10 items$108.9513% off
100 items$104.9516% off
Save this product for later
Customer reviews
Reviews only from verified customers
No reviews yet. You can buy this product and be the first to leave a review.
Share this product with your friends
50:200 (4:1) CUBE™ Current Balun, 1.8-61 MHz, 1.5KW - Loop, OCF, Folded Dipole useful to 200 MHz
Product Details
MPN: CB-4-1500
Country/Region of Manufacture: USA
Type: Balun
Input ohms/Output ohms: 50 in, 200 out
Frequency Range < 2:1 SWR (MHz): 1-31
PEP Power Rating (watts): 1500
Enclosure Size: 4" x4" x 2"
Weight (pounds): 2
Antenna Compatability: Dipoles: Extended double zepp, folded 2 wire, off center fed (OCF); Loops: Horizontal, vertical - coax fed

The CB-4-1500 balun is a multi-core current balun with an enclosure box. Input is via SO-239 coax connector and output can be top studs (for ladder line) or side eye hooks (2) and top eye hook used as a halyard hoist for supporting your wire antenna. Rated 1500 Watts PEP Watts from 1.8-61 MHz (see SWR graph).

This transformer requires a feed line choke to isolate the coax feed line from the antenna. A coax noise filter at the radio end of the coax is also recommended to reduce coax cable common mode noise.is also recommended.

Useful on these type of antennas:

Dipole, double extended
Dipole, linear load, ladder line fed
Dipole, long, non-resonant
Dipole, off-center fed (OCF)
Dipole, snake type, ladder line fed
Long wire with ground system
Multi-band, remote balun


Useful out to 200 MHZ under 2:1 SWR (see swr graph)

Need a 4:1 and 1:1 HYBRID balun? Check out our CB-4-1-1500/5000 with feedline choke built into same box as impedance transformer for ease of installation!


Palomar Engineers offers a variety of impedance transformers configured as Baluns (balanced coax to unbalanced load) or Ununs (unbalanced coax to unbalanced load) for  matching typical 50 ohm feed line impedances to antenna or other load impedances.

We specify impedance ratios as an output to input ratio where the output (or load) is given first and the input is given second (e.g. 100:50 (2:1) would mean a 100 ohm output and a 50 ohm input; a 25:50 (1:2) would mean a 25 ohm load and a 50 ohm input).  Most all products use a 50 ohm input unless otherwise specified.

We have products that are available as kits for the do-it-yourself (DIY) person or fully assembled and tested units for the “Plug & Play” crowd.

Our impedance transformers are available using two different topologies: Binocular cores or  toroid cores with multiple turns for increased effectiveness and wide band frequency transformations.  We utilize single and multiple core transformers using high order windings when needed to extend product performance.

We rate the power ratings as watts PEP (Peak Envelop Power) with standard duty cycles for various modes. To determine the PEP rating required for your needs, see: Choke & Transformer Power Ratings

This website page serves as a link page to the frequency ranges of our impedance transformers configured as either baluns or ununs.  You can click on a picture to go to the specific page about the products described in the picture.