Off Center Fed (OCF) Dipole Baluns

1615373815 - Off Center Fed (OCF) Dipole Baluns
+3

Yaesu 950/2000 Deluxe Transceiver RFI and Noise Reduction Kit, RFI Range 1-60 MHz, 14 Filters

RFI-YAESU-950
$89.95
In stock
1
Product Details
MPN: RFI-ICOM-7610
Type: NEW
Country/Region of Manufacture: United States
RFI Suppression Range (MHz): 1-60 MHz
# Ferrite Filters: 14
Enclosure Size (inches): n/a
Typical Use:: AC/DC power, RF output x 2, multiple I/O lines

The Yaesu 950/2000 Deluxe RFI and noise filter kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the coax output of your radio, the AC/DC power, USB, ALC/Send, mouse,mic and additional interconnect cables. Kit has 4 ferrite ring filters and 10 ferrite snap on filters and instruction manual. Kit can also be used for the Yaesu 2000

This kit will help reduce or eliminate:

1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.

2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.

3. RFI to your other radios, audio/video systems, computers, telephones, etc.

A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).

These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.

The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.

Use of the chokes often helps cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.

For additional RFI suppression, use a feed line choke at the antenna feed point to suppress common current on the coax feed line and a coax noise filter at the radio end of the coax to reduce common mode noise.


If you use a linear amplifier use an amplifier RFI kit for additional RFI interference suppression.
Save this product for later
Display prices in: USD

Testimonial

Hi Bob,

Radio: Flex-6700 running barefoot -10 to 100 Watts max.
Antenna: MFJ-1216 – 160/80 meter OCFD wire antenna with matching network.
Elevation: Over 60 feet AGL – fully extended.
Installed: Mid November 2013

I operate mainly on the digital modes running less than 50 Watts.  All of the sudden after a few days operating with this antenna, I start to have RFI and my radio was acting up; such as changing bands, SWR changing values, radio failures and turning off. However, when I used my Hy-Gain 18 HT vertical on the same band none of the abnormality occurred.
I contacted MFJ and confirm that what I was noticing was a failure of their “matching network” AKA balun.  They offered no solutions. Then I contacted Palomar Engineers and bought the 1:1 new toroid RF beads.  I called Palomar Engineers and I happened to talked to you directly; regarding the on going issue with the MFJ antenna. I found out that the 1:1 balun was not what I needed (I was miss-informed by MFJ that it was 1:1 matching network.)
You offered to make the required balun 4:1 and the rest is history.

Here are my findings:

  1. No more RFI displayed on the monitors.
  2. Radio not acting up or turning off.
  3. The SWR at 160/80 meter is 1.2:1
  4. No antenna tuner required.  (radio goes to Bypass automatically.)
  5. Worst SWR is on 10 meter with a 2:1 but still usable, with antenna tuner 1.5.
  6. One happy OCFD user!

Thanks to Palomar Engineers design and engineering for solving this issue.

73, Ernest – W4EG