New improved version now goes down to 500 KHz (25 dB common mode AM Broadcast band suppression) and up to 61 MHz < 2:1 SWR. Choose Balun only or add optional dipole wire kit (wire, Insulators, Spade lugs for attachment to balun - assembly required). Center insulator and Balun in one case - 1/4" stainless hardware and 5000 real watts rated!
The SBullet-1B-5000EB is a multi-core current balun with built in feed line choke offering up to 60 dB (on 40 meters) of common mode current rejection (plenty for most applications) to keep RFI off the coax outer braid during transmit operations. The SBullet-1B-5000EB is housed in a waterproof PVC enclosure that is lightweight yet robust in features and makes a great high power antenna feed solution for dipoles and other balanced antennas. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 coax connector and output with dual side eye bolt output and wire strain relief. Rated 5000 Watts PEP Watts from .1-61 MHz. SBullet-1B-5000EB weight is 2 pounds.
This balun/feedline choke keeps TRANSMIT RFI off the coax outer braid while transmitting. If your station suffers from common mode RFI noise on RECEIVE, then use one of our Common Mode Coax Noise Filters (such as the CMNF-5000) that suppresses common mode noise on RECEIVE operations.
Make a FAN DIPOLE using optional dipole kits (e.g. 80/40 would use extra 40 meter dipole if you chose the 80 meter dipole lit for this listing).
NOTE: We rate our Bullet baluns (and ununs) VERY conservatively at 5000 watts PEP with a 50% duty cycle. Some manufacturers selling low cost baluns may use a 5% duty cycle for their PEP rating to make it appear you get a higher rated balun for a lower price, but you may in fact be getting be getting less. Their 1500 watts PEP really means 750 watts continuous or 1500 watts at a 50% duty cycle compared to our 250 watts at 50% duty cycle. Our baluns typically cover a larger frequency range under 2:1 SWR which make your transceiver happy and probably will last longer with less electrical stress.
Remember we over engineer our products, to out perform our competition - just compare the weight of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.
Testimonial
Hi Bob,
Radio: Flex-6700 running barefoot -10 to 100 Watts max.
Antenna: MFJ-1216 – 160/80 meter OCFD wire antenna with matching network.
Elevation: Over 60 feet AGL – fully extended.
Installed: Mid November 2013
I operate mainly on the digital modes running less than 50 Watts. All of the sudden after a few days operating with this antenna, I start to have RFI and my radio was acting up; such as changing bands, SWR changing values, radio failures and turning off. However, when I used my Hy-Gain 18 HT vertical on the same band none of the abnormality occurred.
I contacted MFJ and confirm that what I was noticing was a failure of their “matching network” AKA balun. They offered no solutions. Then I contacted Palomar Engineers and bought the 1:1 new toroid RF beads. I called Palomar Engineers and I happened to talked to you directly; regarding the on going issue with the MFJ antenna. I found out that the 1:1 balun was not what I needed (I was miss-informed by MFJ that it was 1:1 matching network.)
You offered to make the required balun 4:1 and the rest is history.
Here are my findings:
- No more RFI displayed on the monitors.
- Radio not acting up or turning off.
- The SWR at 160/80 meter is 1.2:1
- No antenna tuner required. (radio goes to Bypass automatically.)
- Worst SWR is on 10 meter with a 2:1 but still usable, with antenna tuner 1.5.
- One happy OCFD user!
Thanks to Palomar Engineers design and engineering for solving this issue.
73, Ernest – W4EG