Off Center Fed (OCF) Dipole Baluns

3004608882 - Off Center Fed (OCF) Dipole Baluns
+3

Bullet Hybrid (4:1) HF Balun + 1:1 Choke, 1.8-61 MHz, 500/1500 Watts, OCF, Loop, Folded Dipole Antennas

BULLET-4-1-500EB
$119.95
In stock
1
Product Details
Country/Region of Manufacture: USA
Type: NEW
Input ohms/Output ohms: 50 in, 200 out
Frequency Range < 2:1 SWR (MHz): 1.8-100
PEP Power Rating (watts): 500
Transformer Topology: Braodband Ferrite
Hardware Type: Stainless Steel
Weight (pounds): 2
Antenna Compatability: OCF, Folded Dipole, Loop

The Bullet-4-1-500EB (500 watts PEP) or the SBULLET-4-1-1500EB (1500 watts PEP) are both multi-core, 4:1 (50 ohm to 200 ohm) balun plus a 1:1 feed line choke in a single compact (looks like a bullet) enclosure that is lightweight and easy to transport for your fixed/portable.Common Mode Rejection Ratio (CMRR) up to -30 dB for internal feed line chokes.

Very useful for multi-band Off Center Fed, folded dipole and multi-band loop antenna systems. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 UHF coax connector and output with side eye bolt output.

Dimension of 1500 watt model is 8.5 inches tall, 6.5 inches wide tip to tip on the eyebolts.

Shipping weights are 2 pounds for 500 watt version and 3 pounds for 1500 watt version.



Remember we over engineer our products, to out perform our competition - just compare the weight and frequency range of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.


Save this product for later
Display prices in: USD

Testimonial

Hi Bob,

Radio: Flex-6700 running barefoot -10 to 100 Watts max.
Antenna: MFJ-1216 – 160/80 meter OCFD wire antenna with matching network.
Elevation: Over 60 feet AGL – fully extended.
Installed: Mid November 2013

I operate mainly on the digital modes running less than 50 Watts.  All of the sudden after a few days operating with this antenna, I start to have RFI and my radio was acting up; such as changing bands, SWR changing values, radio failures and turning off. However, when I used my Hy-Gain 18 HT vertical on the same band none of the abnormality occurred.
I contacted MFJ and confirm that what I was noticing was a failure of their “matching network” AKA balun.  They offered no solutions. Then I contacted Palomar Engineers and bought the 1:1 new toroid RF beads.  I called Palomar Engineers and I happened to talked to you directly; regarding the on going issue with the MFJ antenna. I found out that the 1:1 balun was not what I needed (I was miss-informed by MFJ that it was 1:1 matching network.)
You offered to make the required balun 4:1 and the rest is history.

Here are my findings:

  1. No more RFI displayed on the monitors.
  2. Radio not acting up or turning off.
  3. The SWR at 160/80 meter is 1.2:1
  4. No antenna tuner required.  (radio goes to Bypass automatically.)
  5. Worst SWR is on 10 meter with a 2:1 but still usable, with antenna tuner 1.5.
  6. One happy OCFD user!

Thanks to Palomar Engineers design and engineering for solving this issue.

73, Ernest – W4EG