Model CB-6-1500 is a 6:1 (300:50) voltage balun housed in a Nema enclosure box (4″ x 4″ x 2″) with two top studs capable of input power levels up to 1.5KW PEP/500 watts continuous when used with a matched load. The 6:1 ratio takes 50 ohms input and matches to 300 ohms balanced output from 1.8-61 MHz with SWR < 1.5:1 under matched load conditions. A great balun for windoms, OCF antennas >60 feet over ground, Hertz and folded dipole antennas, T2FD etc. Dual core, Ruthroff style balun. Choose version with side eye bolts for wire attachments for OCF dipole use.
Magnetic Long Wire Antenna Matcher (9:1) for SWL, 100 KHz-30 MHzProduct DetailsMPN: MLB-2Palomar Engineers Magnetic long wire antenna matche has been redesigned for shortwave listeners who listen to a broad frequency range from VLF to HF and others needing to match a long wire antenna to 50/75 ohm coax feed line cable.
Specifications: Frequency: 100 KHz – 30 MHz. Input: 50/75 ohms for coaxial cable. Output: High impedance. Connector: SO-239 (for cable), wingnut/solder lug wire lead (for antenna). Mounting: Stainless steel eyebolt. Size: 2.5” diameter. Case: White PVC sealed weatherproof. External ground bolt with wing nut for external counterpoise or separate ground.
The long wire antenna often has a high impedance in the 500-1000 ohm range and the MLB-2 transforms this high impedance close to efficiently couple the received signal to the receiver. A long wire antenna with a matching balun such as the MLB-2 often has a 12 db (2 “S” units) better signal than a long wire without a matching balun.
Typical Installation Diagram
MLB-1/MLB-2 Typical installation diagram
For best results we recommend that the coax feed line be at least 1/4 wavelength on the lowest operating frequency since the coax braid is used as a counterpoise if you don’t use the external counterpoise terminal on the matching unit. We also recommend a feed line choke at the end of the coax feed line near the radio to prevent RFI common mode current (from neighbor noise sources) from interfering with the radio – check out the info below on feed line chokes.
Also available as a complete ready to hang SWL antenna. (see related products).
Palomar Engineers Magnetic long wire antenna matche has been redesigned for shortwave listeners who listen to a broad frequency range from VLF to HF and others needing to match a long wire antenna to 50/75 ohm coax feed line cable.
Specifications: Frequency: 100 KHz – 30 MHz. Input: 50/75 ohms for coaxial cable. Output: High impedance. Connector: SO-239 (for cable), wingnut/solder lug wire lead (for antenna). Mounting: Stainless steel eyebolt. Size: 2.5” diameter. Case: White PVC sealed weatherproof. External ground bolt with wing nut for external counterpoise or separate ground.
The long wire antenna often has a high impedance in the 500-1000 ohm range and the MLB-2 transforms this high impedance close to efficiently couple the received signal to the receiver. A long wire antenna with a matching balun such as the MLB-2 often has a 12 db (2 “S” units) better signal than a long wire without a matching balun.
Typical Installation Diagram
MLB-1/MLB-2 Typical installation diagram
For best results we recommend that the coax feed line be at least 1/4 wavelength on the lowest operating frequency since the coax braid is used as a counterpoise if you don’t use the external counterpoise terminal on the matching unit. We also recommend a feed line choke at the end of the coax feed line near the radio to prevent RFI common mode current (from neighbor noise sources) from interfering with the radio – check out the info below on feed line chokes.
Also available as a complete ready to hang SWL antenna. (see related products).
