Magnetic Long Wire Antenna Matcher (9:1) for SWL, 100 KHz-30 MHzProduct DetailsMPN: MLB-2Palomar Engineers Magnetic long wire antenna matche has been redesigned for shortwave listeners who listen to a broad frequency range from VLF to HF and others needing to match a long wire antenna to 50/75 ohm coax feed line cable.
Specifications: Frequency: 100 KHz – 30 MHz. Input: 50/75 ohms for coaxial cable. Output: High impedance. Connector: SO-239 (for cable), wingnut/solder lug wire lead (for antenna). Mounting: Stainless steel eyebolt. Size: 2.5” diameter. Case: White PVC sealed weatherproof. External ground bolt with wing nut for external counterpoise or separate ground.
The long wire antenna often has a high impedance in the 500-1000 ohm range and the MLB-2 transforms this high impedance close to efficiently couple the received signal to the receiver. A long wire antenna with a matching balun such as the MLB-2 often has a 12 db (2 “S” units) better signal than a long wire without a matching balun.
Typical Installation Diagram
MLB-1/MLB-2 Typical installation diagram
For best results we recommend that the coax feed line be at least 1/4 wavelength on the lowest operating frequency since the coax braid is used as a counterpoise if you don’t use the external counterpoise terminal on the matching unit. We also recommend a feed line choke at the end of the coax feed line near the radio to prevent RFI common mode current (from neighbor noise sources) from interfering with the radio – check out the info below on feed line chokes.
Also available as a complete ready to hang SWL antenna. (see related products).
HF 1-61 MHz coax feed line common mode chokes
Palomar Engineers Magnetic long wire antenna matche has been redesigned for shortwave listeners who listen to a broad frequency range from VLF to HF and others needing to match a long wire antenna to 50/75 ohm coax feed line cable.
Specifications: Frequency: 100 KHz – 30 MHz. Input: 50/75 ohms for coaxial cable. Output: High impedance. Connector: SO-239 (for cable), wingnut/solder lug wire lead (for antenna). Mounting: Stainless steel eyebolt. Size: 2.5” diameter. Case: White PVC sealed weatherproof. External ground bolt with wing nut for external counterpoise or separate ground.
The long wire antenna often has a high impedance in the 500-1000 ohm range and the MLB-2 transforms this high impedance close to efficiently couple the received signal to the receiver. A long wire antenna with a matching balun such as the MLB-2 often has a 12 db (2 “S” units) better signal than a long wire without a matching balun.
Typical Installation Diagram
MLB-1/MLB-2 Typical installation diagram
For best results we recommend that the coax feed line be at least 1/4 wavelength on the lowest operating frequency since the coax braid is used as a counterpoise if you don’t use the external counterpoise terminal on the matching unit. We also recommend a feed line choke at the end of the coax feed line near the radio to prevent RFI common mode current (from neighbor noise sources) from interfering with the radio – check out the info below on feed line chokes.
Also available as a complete ready to hang SWL antenna. (see related products).
1:1 feed line Chokes (also known as feed line current chokes, common mode chokes, line isolators, current mode chokes, and 1:1 baluns/ununs) are available in kit form or assembled form in a weatherproof Current Unun and Balun Enclosure which we call a CUBE™. All 1:1 chokes are ferrite based and are designed for 50 ohm coaxial cable input and 50 ohm output. 1:1 Ferrite toroidal or bead chokes have a higher choking impedance than our popular Sleeve Chokes and various models are available for specific frequency ranges and power levels.
1:1 Chokes are useful for choking common mode currents that may flow on the exterior of the coax cable shield while allowing the signals on the interior of the shield and the center conductor to flow unaffected and keeping the common mode current on the antenna. They isolate the coax shield and prevent it from becoming part of the antenna system.
1:1 Chokes are useful between balanced lines for center fed dipoles at their fundamental frequency (468/f (MHz), beam antennas with a 50 ohm balanced driven element, G5RV, loops, yagis, NVIS antennas, mobile installations, portable antennas and anywhere common mode current (or RFI) is a problem. They are also helpful between transmitter and linear amplifier or between linear amp and antenna tuner or as isolation chokes where higher choking impedance is needed (in the range of 2K-7K ohms).
1:1 Chokes are also very useful as feed line current chokes at the “radio end” of the antenna (we call them coax noise filters) where they choke/filter common mode current induced onto the coax shield from radiated waves (from your antenna, and other sources such as DSL routers, computer devices, plasma TVs, etc. originating in your house or your neighbor’s house). For RFI issues see RFI/EMI Solutions for general use or for specific radios and devices.
For best results we recommend a 1:1 choke at the “antenna end” of the coax and a coax noise filter at the “radio end” of the coax. (A side benefit is a reduction in noise level caused by common mode currents). 1:1 chokes are also available as Sleeve Chokes (Slip on or Snap on) for ease of installation and light weight on the antenna.