CUBE 1:1 Feed Line Choke Balun, 1.5KW, 1.8-61 MHz Eyebolt Version - DipolesProduct DetailsBrand: Palomar EngineersEffective Frequency Range (MHz): 1-61 MHzPEP Power Rating (watts): 1500Common Mode Attenuation (db): up to -38 dBEstimated Insertion Loss (db): .10Input Connector Type: SO-239 femaleOutput Connector Connector Type: side eyebolts and top halyard hoistEnclosure Size (LxWxH inches): 4 x 4 x 21500 Watt PEP Rated 1:1 CUBE™ Balun for dipoles
* Help keep RF out of the shack.
* Provides maximum transfer of RF to the antenna.
* Suppress radiation from the feeder cable
* Makes the antenna radiation pattern predictable.
* Outperforms the competition by 24 dB common mode rejection! (see graphs)
* Reduces QRN and TVI to the neighbors.
The CB-1-1500 balun is useful as common mode feed line chokes or unbalanced coax to balanced antenna interface. SO-239 input to side terminal/eyebolt output. . Rated 1500 Watts PEP from 1-61 MHz. Common mode rejection up to -38dB over the frequency range. The CB-1-1500 is the balun version and the CU-1-1500 is the unun version (coax in and coax out).
Use as line isolator, antenna interface, or as a common mode choke to keep RF on the antenna and off the outside of the coax braid. Much more effective then our snap on ferrite beads as this balun which provides a higher choking impedance over a broad frequency range.
For most effective results, use another feed line choke (coax noise filter) at the radio. Helps reduce noise floor too by choking off common mode neighborhood noise picked up on outside of coax braid acting as secondary receive antenna
Other cool products
HF 1-61 MHz coax feed line common mode chokes
1500 Watt PEP Rated 1:1 CUBE™ Balun for dipoles
* Help keep RF out of the shack.
* Provides maximum transfer of RF to the antenna.
* Suppress radiation from the feeder cable
* Makes the antenna radiation pattern predictable.
* Outperforms the competition by 24 dB common mode rejection! (see graphs)
* Reduces QRN and TVI to the neighbors.
The CB-1-1500 balun is useful as common mode feed line chokes or unbalanced coax to balanced antenna interface. SO-239 input to side terminal/eyebolt output. . Rated 1500 Watts PEP from 1-61 MHz. Common mode rejection up to -38dB over the frequency range. The CB-1-1500 is the balun version and the CU-1-1500 is the unun version (coax in and coax out).
Use as line isolator, antenna interface, or as a common mode choke to keep RF on the antenna and off the outside of the coax braid. Much more effective then our snap on ferrite beads as this balun which provides a higher choking impedance over a broad frequency range.
For most effective results, use another feed line choke (coax noise filter) at the radio. Helps reduce noise floor too by choking off common mode neighborhood noise picked up on outside of coax braid acting as secondary receive antenna
1:1 feed line Chokes (also known as feed line current chokes, common mode chokes, line isolators, current mode chokes, and 1:1 baluns/ununs) are available in kit form or assembled form in a weatherproof Current Unun and Balun Enclosure which we call a CUBE™. All 1:1 chokes are ferrite based and are designed for 50 ohm coaxial cable input and 50 ohm output. 1:1 Ferrite toroidal or bead chokes have a higher choking impedance than our popular Sleeve Chokes and various models are available for specific frequency ranges and power levels.
1:1 Chokes are useful for choking common mode currents that may flow on the exterior of the coax cable shield while allowing the signals on the interior of the shield and the center conductor to flow unaffected and keeping the common mode current on the antenna. They isolate the coax shield and prevent it from becoming part of the antenna system.
1:1 Chokes are useful between balanced lines for center fed dipoles at their fundamental frequency (468/f (MHz), beam antennas with a 50 ohm balanced driven element, G5RV, loops, yagis, NVIS antennas, mobile installations, portable antennas and anywhere common mode current (or RFI) is a problem. They are also helpful between transmitter and linear amplifier or between linear amp and antenna tuner or as isolation chokes where higher choking impedance is needed (in the range of 2K-7K ohms).
1:1 Chokes are also very useful as feed line current chokes at the “radio end” of the antenna (we call them coax noise filters) where they choke/filter common mode current induced onto the coax shield from radiated waves (from your antenna, and other sources such as DSL routers, computer devices, plasma TVs, etc. originating in your house or your neighbor’s house). For RFI issues see RFI/EMI Solutions for general use or for specific radios and devices.
For best results we recommend a 1:1 choke at the “antenna end” of the coax and a coax noise filter at the “radio end” of the coax. (A side benefit is a reduction in noise level caused by common mode currents). 1:1 chokes are also available as Sleeve Chokes (Slip on or Snap on) for ease of installation and light weight on the antenna.