Bullet Hybrid (2:1) HF Balun + 1:1 Choke, 1.8-61 MHz, 500/1500 Watts, OCF, Loop, Folded Dipole AntennasProduct DetailsCountry/Region of Manufacture: USAType: NEWInput ohms/Output ohms: 50 in, 100 outFrequency Range < 2:1 SWR (MHz): 1.8-100PEP Power Rating (watts): 500Input Connector: SO239Transformer Topology: Braodband FerriteHardware Type: Stainless SteelWeight (pounds): 2Antenna Compatability: LoopThe Bullet-2-1-500EB (500 watts PEP) or the SBULLET-2-1-1500EB (1500 watts PEP) are both multi-core, 2:1 (50 ohm to 100 ohm) baluns plus a 1:1 feed line choke in a single compact (looks like a bullet) enclosure that is lightweight and easy to transport for your fixed/portable.
Very useful for single band horizontal or vertical loop antenna systems. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 UHF coax connector and output with side eye bolt output.
For multi-band loop antennas consider the Bullet-4-1-500EB or SBULLET-4-1-1500EB
Remember we over engineer our products, to out perform our competition - just compare the weight and frequency range of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.
HF 1-61 MHz coax feed line common mode chokes
The Bullet-2-1-500EB (500 watts PEP) or the SBULLET-2-1-1500EB (1500 watts PEP) are both multi-core, 2:1 (50 ohm to 100 ohm) baluns plus a 1:1 feed line choke in a single compact (looks like a bullet) enclosure that is lightweight and easy to transport for your fixed/portable.
Very useful for single band horizontal or vertical loop antenna systems. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 UHF coax connector and output with side eye bolt output.
For multi-band loop antennas consider the Bullet-4-1-500EB or SBULLET-4-1-1500EB
Remember we over engineer our products, to out perform our competition - just compare the weight and frequency range of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.
1:1 feed line Chokes (also known as feed line current chokes, common mode chokes, line isolators, current mode chokes, and 1:1 baluns/ununs) are available in kit form or assembled form in a weatherproof Current Unun and Balun Enclosure which we call a CUBE™. All 1:1 chokes are ferrite based and are designed for 50 ohm coaxial cable input and 50 ohm output. 1:1 Ferrite toroidal or bead chokes have a higher choking impedance than our popular Sleeve Chokes and various models are available for specific frequency ranges and power levels.
1:1 Chokes are useful for choking common mode currents that may flow on the exterior of the coax cable shield while allowing the signals on the interior of the shield and the center conductor to flow unaffected and keeping the common mode current on the antenna. They isolate the coax shield and prevent it from becoming part of the antenna system.
1:1 Chokes are useful between balanced lines for center fed dipoles at their fundamental frequency (468/f (MHz), beam antennas with a 50 ohm balanced driven element, G5RV, loops, yagis, NVIS antennas, mobile installations, portable antennas and anywhere common mode current (or RFI) is a problem. They are also helpful between transmitter and linear amplifier or between linear amp and antenna tuner or as isolation chokes where higher choking impedance is needed (in the range of 2K-7K ohms).
1:1 Chokes are also very useful as feed line current chokes at the “radio end” of the antenna (we call them coax noise filters) where they choke/filter common mode current induced onto the coax shield from radiated waves (from your antenna, and other sources such as DSL routers, computer devices, plasma TVs, etc. originating in your house or your neighbor’s house). For RFI issues see RFI/EMI Solutions for general use or for specific radios and devices.
For best results we recommend a 1:1 choke at the “antenna end” of the coax and a coax noise filter at the “radio end” of the coax. (A side benefit is a reduction in noise level caused by common mode currents). 1:1 chokes are also available as Sleeve Chokes (Slip on or Snap on) for ease of installation and light weight on the antenna.