50:50 (1:1) CUBE™ Ladder Line/Beam to Coax Balun, 1.8-61 MHz, 1.5KW, G5RV/ZS6BKW/Dipole/BeamProduct DetailsMPN: CB-1-1500TSCountry/Region of Manufacture: USAInput ohms/Output ohms: 50 ohms in, 50 - 150 ouhms outputFrequency Range < 2:1 SWR (MHz): 1.8-61 MHzPEP Power Rating (watts): 1500Input Connector: UHF or NOutput Connector(s): top studsHardware Type: Stainless Steel output connectorsEnclosure Size: 4 x 4 x 2Antenna Compatability: G5RV/ZS6BKW/Dipole/balanced outputThe lower powered version of our popular CB-1-5000, the CB-1-1500TS Balun is a 50 ohm to 50 ohm, quad core feed line choke designed to provide high choking impedance between a balanced ladder line feed line (zepp, G5RV/ZS6BKW, extended double zepp, etc.) and short 50 ohm coax feed line (to antenna tuner) at a power of 1500 watts PEP from 1.8 to 61 MHz. The CB-1-1500TS is configured as a Guanilla transmission line transformer with balanced outputs (current balun configuration). It is best used when ladder line impedance seen at the end of the ladder line to balun connection is close to 50-150 ohms. Enclosure box is 4″ x 4″ x 2″. Typical choking impedance range is 1K-10K ohms from 1-61 MHz and common mode suppression is 30 dB..
Typical ZS6BKW multi-band antenna with CB-1-1500 or CB-1-5000
N Connector versions are made to order, email for quantity production times
HF 1-61 MHz coax feed line common mode chokes
The lower powered version of our popular CB-1-5000, the CB-1-1500TS Balun is a 50 ohm to 50 ohm, quad core feed line choke designed to provide high choking impedance between a balanced ladder line feed line (zepp, G5RV/ZS6BKW, extended double zepp, etc.) and short 50 ohm coax feed line (to antenna tuner) at a power of 1500 watts PEP from 1.8 to 61 MHz. The CB-1-1500TS is configured as a Guanilla transmission line transformer with balanced outputs (current balun configuration). It is best used when ladder line impedance seen at the end of the ladder line to balun connection is close to 50-150 ohms. Enclosure box is 4″ x 4″ x 2″. Typical choking impedance range is 1K-10K ohms from 1-61 MHz and common mode suppression is 30 dB..
Typical ZS6BKW multi-band antenna with CB-1-1500 or CB-1-5000
N Connector versions are made to order, email for quantity production times
1:1 feed line Chokes (also known as feed line current chokes, common mode chokes, line isolators, current mode chokes, and 1:1 baluns/ununs) are available in kit form or assembled form in a weatherproof Current Unun and Balun Enclosure which we call a CUBE™. All 1:1 chokes are ferrite based and are designed for 50 ohm coaxial cable input and 50 ohm output. 1:1 Ferrite toroidal or bead chokes have a higher choking impedance than our popular Sleeve Chokes and various models are available for specific frequency ranges and power levels.
1:1 Chokes are useful for choking common mode currents that may flow on the exterior of the coax cable shield while allowing the signals on the interior of the shield and the center conductor to flow unaffected and keeping the common mode current on the antenna. They isolate the coax shield and prevent it from becoming part of the antenna system.
1:1 Chokes are useful between balanced lines for center fed dipoles at their fundamental frequency (468/f (MHz), beam antennas with a 50 ohm balanced driven element, G5RV, loops, yagis, NVIS antennas, mobile installations, portable antennas and anywhere common mode current (or RFI) is a problem. They are also helpful between transmitter and linear amplifier or between linear amp and antenna tuner or as isolation chokes where higher choking impedance is needed (in the range of 2K-7K ohms).
1:1 Chokes are also very useful as feed line current chokes at the “radio end” of the antenna (we call them coax noise filters) where they choke/filter common mode current induced onto the coax shield from radiated waves (from your antenna, and other sources such as DSL routers, computer devices, plasma TVs, etc. originating in your house or your neighbor’s house). For RFI issues see RFI/EMI Solutions for general use or for specific radios and devices.
For best results we recommend a 1:1 choke at the “antenna end” of the coax and a coax noise filter at the “radio end” of the coax. (A side benefit is a reduction in noise level caused by common mode currents). 1:1 chokes are also available as Sleeve Chokes (Slip on or Snap on) for ease of installation and light weight on the antenna.