BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH MANY BRANDS OF HAM/COMMERCIAL HF RADIOS WITH DUAL ANTENNAS OUTPUTS AND MULTIPLE I/O CONNECTIONS INCLUDING THE YAESU 991
Kit Includes 3 noise reduction 1.4" ID ring filters for two coax cables, AC/DC power and 5 1/2" ID snap on filters for I/O cables covering RFI range of 1-300 MHz. Quick installation - immediate RFI/noise reduction. No radio mods required.
This kit will help reduce or eliminate:
1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.
2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.
3. RFI to your other radios, audio/video systems, computers, telephones, etc.
A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).
These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.
The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.
Use of the chokes often helps cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.
For additional RFI suppression, use a feed line choke at the antenna feed point to suppress common current on the coax feed line and a coax noise filter (like our CMNF-500-50) at the radio end of the coax to reduce common mode noise.If you use a linear amplifier use a Palomar Engineers amplifier RFI kit for additional RFI interference suppression.
Due to many requests for antenna static bleeders, we have developed a product line of static bleeders for coax and for ladder line applications. Static electricity is caused by many situations including high desert wind, atmospheric conditions, etc. You may hear static crashes or have a buildup of static electricity that my be annoying during a radio conversation and it may be harmful to solid state electronics if high voltages are present on the RF input to your equipment.
A static “Bleeder” which shorts the direct static voltage to ground while leaving the RF frequency voltage unaffected if very beneficial particularly to those operations in desert conditions where low humidity, high static buildup are quite common. The SB-1 and SB-2 coax static bleeders work on coax line and the SB-3 static bleeder is meant for ladder line.
THESE DEVICES ARE NOT FOR LIGHTNING PROTECTION AND PROVIDES NO PROTECTION FOR LIGHTNING STRIKES!!!!!
BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH MANY BRANDS OF HAM/COMMERCIAL HF RADIOS WITH DUAL ANTENNAS OUTPUTS AND MULTIPLE I/O CONNECTIONS INCLUDING THE YAESU 991
Kit Includes 3 noise reduction 1.4" ID ring filters for two coax cables, AC/DC power and 5 1/2" ID snap on filters for I/O cables covering RFI range of 1-300 MHz. Quick installation - immediate RFI/noise reduction. No radio mods required.
This kit will help reduce or eliminate:
1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.
2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.
3. RFI to your other radios, audio/video systems, computers, telephones, etc.
A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).
These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.
The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.
Use of the chokes often helps cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.
For additional RFI suppression, use a feed line choke at the antenna feed point to suppress common current on the coax feed line and a coax noise filter (like our CMNF-500-50) at the radio end of the coax to reduce common mode noise.If you use a linear amplifier use a Palomar Engineers amplifier RFI kit for additional RFI interference suppression.