Palomar Engineers RFI Filter Kit for CB Radio Radio Transceivers from 20-30 MHz uses ferrite rings for the DC power supply and the coax to the antenna.
BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH ALL BRANDS (Cobra, DAS, Midland, Uniden etc.) OF CB/HAM/COMMERCIAL RADIO RIGS in 20-60 MHz range.
Purpose
The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and on the DC power supply cable.
This kit will help reduce or eliminate:
1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.
2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.
3. RFI to your other radios, audio/video systems, computers, telephones, etc.
A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).
These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from Ham Radio amplifiers.
Included are the following chokes and installation guidelines:
DC Input: F240 Ring – 3-7 turns of DC power cable - sized for smaller plugs
RF Input/Output: F240-31 ring - wrap 6 turns of RG8X size cable near the back of the radio
For additional RFI suppression, use a MC-1-500-50 mini feed line choke at the antenna feed point to suppress common current on the coax feed line during transmit and a CMNF-500-50 Coax Noise Filter to reduce common mode noise during receive operations.
If you use a switching power supply for base operation, consider the RFI-SMPS switching power supply RFI kit.
If you use a linear amplifier we have RFI kits for linear amplifiers that help suppress RFI in your shack or in your neighbor’s house.
Due to many requests for antenna static bleeders, we have developed a product line of static bleeders for coax and for ladder line applications. Static electricity is caused by many situations including high desert wind, atmospheric conditions, etc. You may hear static crashes or have a buildup of static electricity that my be annoying during a radio conversation and it may be harmful to solid state electronics if high voltages are present on the RF input to your equipment.
A static “Bleeder” which shorts the direct static voltage to ground while leaving the RF frequency voltage unaffected if very beneficial particularly to those operations in desert conditions where low humidity, high static buildup are quite common. The SB-1 and SB-2 coax static bleeders work on coax line and the SB-3 static bleeder is meant for ladder line.
THESE DEVICES ARE NOT FOR LIGHTNING PROTECTION AND PROVIDES NO PROTECTION FOR LIGHTNING STRIKES!!!!!
Palomar Engineers RFI Filter Kit for CB Radio Radio Transceivers from 20-30 MHz uses ferrite rings for the DC power supply and the coax to the antenna.
BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH ALL BRANDS (Cobra, DAS, Midland, Uniden etc.) OF CB/HAM/COMMERCIAL RADIO RIGS in 20-60 MHz range.
Purpose
The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and on the DC power supply cable.
This kit will help reduce or eliminate:
1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.
2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.
3. RFI to your other radios, audio/video systems, computers, telephones, etc.
A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).
These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from Ham Radio amplifiers.
Included are the following chokes and installation guidelines:
DC Input: F240 Ring – 3-7 turns of DC power cable - sized for smaller plugs
RF Input/Output: F240-31 ring - wrap 6 turns of RG8X size cable near the back of the radio
For additional RFI suppression, use a MC-1-500-50 mini feed line choke at the antenna feed point to suppress common current on the coax feed line during transmit and a CMNF-500-50 Coax Noise Filter to reduce common mode noise during receive operations.
If you use a switching power supply for base operation, consider the RFI-SMPS switching power supply RFI kit.
If you use a linear amplifier we have RFI kits for linear amplifiers that help suppress RFI in your shack or in your neighbor’s house.