The Bullet-4B-500 and SBullet-4B-1500 are multi-core core baluns with a compact enclosure (looks like a bullet) enclosure that is physically lightweight but electrically robust and easy to transport for your portable loop antenna solution or permanent installation. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 coax connector and output with side eye bolt output. Choose your model rated 500 or 1500 Watts PEP from 1.8-61 MHz.
This transformer requires a feed line choke (see related products) to isolate the coax feed line from the antenna. A coax noise filter at the radio end of the coax is also recommended for best results.
Vertical Delta Loops
Multi-band vertical delta loops can be oriented several way but the most popular is to have the “pointy” end at the top (usually a single support) and the lower horizontal ends just out of reach of humans and animals. Best feed point at the top for multi-band use with a 4;1 balun. CUt total wire length to 1005/F (MHz) where F is lowest band frequency of use..
Single band vertical delta loops are best fed 1/4 wavelength (246/f(MHz)) from the top point down one side. Vertical delta loops use the same 2:1 baluns as the horizontal loops.
NOTE: We rate our Bullet baluns (and ununs) VERY conservatively at 500 watts PEP with a 50% duty cycle. Some manufacturers selling low cost baluns may use a 5% duty cycle for their PEP rating to make it appear you get a higher rated balun for a lower price, but you may in fact be getting be getting less. Their 1500 watts PEP really means 75 watts continuous or 150 watts at a 50% duty cycle compared to our 250 watts at 50% duty cycle. Our baluns typically cover a larger frequency range under 2:1 SWR which make your transceiver happy and probably will last longer with less electrical stress.
Remember we over engineer our products, to out perform our competition - just compare the weight of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.
Due to many requests for antenna static bleeders, we have developed a product line of static bleeders for coax and for ladder line applications. Static electricity is caused by many situations including high desert wind, atmospheric conditions, etc. You may hear static crashes or have a buildup of static electricity that my be annoying during a radio conversation and it may be harmful to solid state electronics if high voltages are present on the RF input to your equipment.
A static “Bleeder” which shorts the direct static voltage to ground while leaving the RF frequency voltage unaffected if very beneficial particularly to those operations in desert conditions where low humidity, high static buildup are quite common. The SB-1 and SB-2 coax static bleeders work on coax line and the SB-3 static bleeder is meant for ladder line.
THESE DEVICES ARE NOT FOR LIGHTNING PROTECTION AND PROVIDES NO PROTECTION FOR LIGHTNING STRIKES!!!!!
The Bullet-4B-500 and SBullet-4B-1500 are multi-core core baluns with a compact enclosure (looks like a bullet) enclosure that is physically lightweight but electrically robust and easy to transport for your portable loop antenna solution or permanent installation. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 coax connector and output with side eye bolt output. Choose your model rated 500 or 1500 Watts PEP from 1.8-61 MHz.
This transformer requires a feed line choke (see related products) to isolate the coax feed line from the antenna. A coax noise filter at the radio end of the coax is also recommended for best results.
Vertical Delta Loops
Multi-band vertical delta loops can be oriented several way but the most popular is to have the “pointy” end at the top (usually a single support) and the lower horizontal ends just out of reach of humans and animals. Best feed point at the top for multi-band use with a 4;1 balun. CUt total wire length to 1005/F (MHz) where F is lowest band frequency of use..
Single band vertical delta loops are best fed 1/4 wavelength (246/f(MHz)) from the top point down one side. Vertical delta loops use the same 2:1 baluns as the horizontal loops.
NOTE: We rate our Bullet baluns (and ununs) VERY conservatively at 500 watts PEP with a 50% duty cycle. Some manufacturers selling low cost baluns may use a 5% duty cycle for their PEP rating to make it appear you get a higher rated balun for a lower price, but you may in fact be getting be getting less. Their 1500 watts PEP really means 75 watts continuous or 150 watts at a 50% duty cycle compared to our 250 watts at 50% duty cycle. Our baluns typically cover a larger frequency range under 2:1 SWR which make your transceiver happy and probably will last longer with less electrical stress.
Remember we over engineer our products, to out perform our competition - just compare the weight of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.