Model BA-1-1500 is a 1:1 balun kit used to translate a 50 ohm unbalanced input to 50 ohms unbalanced at power levels up to 1500 watts PEP when used with a matched load. With a matched load the SWR will not exceed 1.5 over the frequency range 1.8 to 30 MHz. 1,500 PEP watt rating on a 25% duty cycle.
The kit consists of a F240 ferrite core, two colors of selected insulated wire, two SO-239 connectors (one for input and one for output connections) with stainless steel hardware, and an illustrated instruction manual with directions to assemble the kit as a 1 to 1 balun (unbalanced coax to balanced antenna/load) or unun (unbalanced to unbalanced). Leave one of the SO-239 connectors off on the output side and connect to your balanced antenna (dipole, beam driven elements, etc). To use as a line isolator/common mode choke, use both SO-239 connectors and insert in series with the coax feed line. For best results use one at the antenna and one for the rig side at the antenna tuner. The number of turns on the toroid can be changed to emphasize the low, mid or high portion of the 160-10 meter bands range as well as the choking impedance (see graph below). Assembly time is about 30 minutes. You can vary the number of turns to emphasize different frequency ranges.
BA-1-1500 Choking Z magnitude – 14 Turns and 10 Turns
Just add your custom enclosure, or optional enclosure box below, with the kit and you have a compete 1:1 current balun/unun.
Due to many requests for antenna static bleeders, we have developed a product line of static bleeders for coax and for ladder line applications. Static electricity is caused by many situations including high desert wind, atmospheric conditions, etc. You may hear static crashes or have a buildup of static electricity that my be annoying during a radio conversation and it may be harmful to solid state electronics if high voltages are present on the RF input to your equipment.
A static “Bleeder” which shorts the direct static voltage to ground while leaving the RF frequency voltage unaffected if very beneficial particularly to those operations in desert conditions where low humidity, high static buildup are quite common. The SB-1 and SB-2 coax static bleeders work on coax line and the SB-3 static bleeder is meant for ladder line.
THESE DEVICES ARE NOT FOR LIGHTNING PROTECTION AND PROVIDES NO PROTECTION FOR LIGHTNING STRIKES!!!!!
Model BA-1-1500 is a 1:1 balun kit used to translate a 50 ohm unbalanced input to 50 ohms unbalanced at power levels up to 1500 watts PEP when used with a matched load. With a matched load the SWR will not exceed 1.5 over the frequency range 1.8 to 30 MHz. 1,500 PEP watt rating on a 25% duty cycle.
The kit consists of a F240 ferrite core, two colors of selected insulated wire, two SO-239 connectors (one for input and one for output connections) with stainless steel hardware, and an illustrated instruction manual with directions to assemble the kit as a 1 to 1 balun (unbalanced coax to balanced antenna/load) or unun (unbalanced to unbalanced). Leave one of the SO-239 connectors off on the output side and connect to your balanced antenna (dipole, beam driven elements, etc). To use as a line isolator/common mode choke, use both SO-239 connectors and insert in series with the coax feed line. For best results use one at the antenna and one for the rig side at the antenna tuner. The number of turns on the toroid can be changed to emphasize the low, mid or high portion of the 160-10 meter bands range as well as the choking impedance (see graph below). Assembly time is about 30 minutes. You can vary the number of turns to emphasize different frequency ranges.
BA-1-1500 Choking Z magnitude – 14 Turns and 10 Turns
Just add your custom enclosure, or optional enclosure box below, with the kit and you have a compete 1:1 current balun/unun.