50:250 ohm (5:1) CUBE™ Unun™, 1.8-61 Mz, 1500 Watts, end fed, vertical
CU-5-1500
$129.95
In stock
1
Product Details
MPN:
CU-5-1500
Input ohms/Output ohms:
50 in / 250 output
Frequency Range < 2:1 SWR (MHz):
1-31
PEP Power Rating (watts):
1500
Model CU-5-1500EB- 5 to 1 Unun
(SO-239 in/Eye bolt hoist with output connector on top, side stud for ground/counterpoise)
Purpose. This unun is designed to match 250 ohms unbalanced to 50 ohms unbalanced up to 1500 watts PEP power from 1.8-61 MHz. It provides conversion from unbalanced 50 ohm coax to an unbalanced 250 ohm load/antenna feed point and gives a 5:1 impedance step-up to reduce VSWR on the coax feed line. The unun is housed in a 4” x 4” X “2 NEMA weather resistant box with SO-239 coaxial input and a ¼” stud terminal with wing nut on the top for output and another on the side for ground or counterpoise connection.
This unun is DC grounded and will bleed off static electricity but it is NOT A LIGHTNING ARRESTOR.
Model CU-5-1500 is a 50 ohm to 250 ohm (5:1) voltage unun used to translate a 50 ohm input up to 250 ohms at RF power levels up to 1500 watts PEP (30% duty cycle) when used with a matched load. With a matched 250 ohm unbalanced load SWR should not exceed 2.0 over the frequency range 1.8-61 MHz.
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 balun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical Antenna System Using CU-5-1500
Use a coax noise filter to reduce noise from any vertical antenna or a line isolator to suppress coax cable braid radiation on transmit.
Save this product for later
Super-Choker™ Common Mode Feed Line Chokes
50:250 ohm (5:1) CUBE™ Unun™, 1.8-61 Mz, 1500 Watts, end fed, vertical
Model CU-5-1500EB- 5 to 1 Unun
(SO-239 in/Eye bolt hoist with output connector on top, side stud for ground/counterpoise)
Purpose. This unun is designed to match 250 ohms unbalanced to 50 ohms unbalanced up to 1500 watts PEP power from 1.8-61 MHz. It provides conversion from unbalanced 50 ohm coax to an unbalanced 250 ohm load/antenna feed point and gives a 5:1 impedance step-up to reduce VSWR on the coax feed line. The unun is housed in a 4” x 4” X “2 NEMA weather resistant box with SO-239 coaxial input and a ¼” stud terminal with wing nut on the top for output and another on the side for ground or counterpoise connection.
This unun is DC grounded and will bleed off static electricity but it is NOT A LIGHTNING ARRESTOR.
Model CU-5-1500 is a 50 ohm to 250 ohm (5:1) voltage unun used to translate a 50 ohm input up to 250 ohms at RF power levels up to 1500 watts PEP (30% duty cycle) when used with a matched load. With a matched 250 ohm unbalanced load SWR should not exceed 2.0 over the frequency range 1.8-61 MHz.
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 balun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical Antenna System Using CU-5-1500
Use a coax noise filter to reduce noise from any vertical antenna or a line isolator to suppress coax cable braid radiation on transmit.
Sometimes you need a high power common mode choke that is super effective and the Super-Choker™ products fill this need very well. All Super-Choker™ chokes use multiple turns through ferrite cores for higher choking impedance compared to our multi-bead sleeve chokes which only use one turn through multiple cores. Different ferrite mixes and turns ratios are used to optimize choking impedance in the selected product frequency range.
Super-Choker™ chokes are manufactured with 1/2″ 52 ohm coax cable (rated for full amateur radio legal limit of 1500 watts continuous (or the capacity of the coax cable at the selected frequency – good for over 5KW on 4 MHz into a matched load for example) with PL-259 connectors that can be connected to your coax feed line with simple double female barrel connectors.
Super-Choker™ chokes are ideal for high power stations and are very effective for keeping common mode current off the feed line on verticals, dipoles, and loop antennas at their feed point and also for choking coax lines at the station input to reduce common mode noise picked up by the outside of the coax braid between the feed point and the station entrance.
Ferrite core kits are available separately if you want to supply your own coax feed line.
Super Choker™ Case History:
I run an 80 meter loop antenna about 30 feet in height and have previously been using a coaxial balun common mode choke of 25 turns of RG-213 on a 6 inch form attached about 6 feet under the corner feed point of the loop (configured in a triangle). Using a Dentron 3000 antenna tuner I was able to tune all the ham bands and the lowest SWR was about 1.4 on most bands. The antenna feed line was led away from the corner of the loop and was not under the loop. Feed line length was about 105 feet as measured on the Aim 4170-TDR function.
I first placed a Super Choker™ 8010 at the antenna tuner leaving the coaxial balun in place. As I retuned the antenna tuner, the first thing I noticed was that I could now tune down to 1.1:1 on 80, 40 and 20 meters and I could not do that before. The noise level which had been running about S7 on 40 meters during the day had dropped to about S6 on my TS-870 receiver. I was pleased that the reflected power was now almost nil and the noise level was lower.
I then took the next step and replaced the coaxial balun and Super Choker 8010 with a Super Choker™ 16040 in series with a Super Choker 4010 for maximum choking power from 80-10meters. The antenna tuning was about the same but now the SWR was 1.0:1 on 80-10 meters and the noise level on 40 was down to S5. I tuned up on 20, 15 and 10 meters and worked a couple of JA’s and noticed that the noise level on 10 and 15 was not even S1 – something I had not experienced before on the 5 acre plot of land we call home.
What a welcome relief to find such a simple solution to RF feedback I had experienced and I got a lower noise level to boot!
Now to plan that 160 meter loop! I wonder what Krusty ole Kurt would use?
Bob, AK6R