Portable Operation RFI Kits

VHF/UHF Generic Base Transceiver RFI Kit

SKU RFI-VHF-BASE
$49.95
Bulk pricing available for quantities of 10 units or more
1
Buy more, save more
QuantityPrice per itemDiscount
10 items$35.0030% off
Save this product for later
Customer reviews
No reviews yet. Only signed-in customers who bought this product can leave reviews. To leave a review, sign in
Share this product with your friends
VHF/UHF Generic Base Transceiver RFI Kit
Product Details
MPN: RFI-VHF-BASE
Type: Nw
Country/Region of Manufacture: United States
Filter Power Rating (PEP watts): 500
RFI Suppression Range (MHz): 25-300 MHz

Palomar Engineers RFI Filter Kit for VHF/UHF Base Radio Transceivers up to 2 GHz uses a combination of ferrite mixes useful from 1-2000 MHz.

BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH MANY BRANDS OF HAM/COMMERCIAL RADIO RIGS


Purpose

The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio. Additional chokes are included to reduce common mode currents on the amp relay keying line (7 pin Din), rear audio in/out for digital modes (13 pin Din), computer control line (DB-9) and the DC power cord.

This kit will help reduce or eliminate:

1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.

2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.

3. RFI to your other radios, audio/video systems, computers, telephones, etc.

A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).

These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from Ham Radio amplifiers.

The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.

This kit is designed to choke common mode currents going into or exiting from your transceiver. Chokes are supplied for the RF Out (1 antenna only), Amp Relay Cable (7 pin DIN), Computer Control Cable (DB-9), PSK31/Digital Mode Cable (13 pin Din) and DC power line. Use of the chokes often helps cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.

Included are the following chokes and installation guidelines:

RF Input: F240 Ring Toroid for noise reduction – 3-5 turns of RG-58/RG-8X size coax cable through center

DC Input: F240 Ring Toroid – 3-7 turns of DC power cable

I/O Cable 1: FSB-1/2 – multiple turns through choke – ½” diameter hole

I/O Cable 2: FSB-1/2 – multiple turns through choke – ½” diameter hole

I/O Cable 3: FSB-1/2 – multiple turns through choke – ½” diameter hole

Also make sure you connect a good RF ground to the transceiver ground post.

For additional RFI suppression, use a feed line choke at the antenna to suppress common current on the coax feed line – see our store for feed line choke alternatives for use at the antenna.

If you use a linear amplifier we have RFI kits for linear amplifiers that help suppress RFI in your shack or in your neighbor’s house.

Portable operation is fun but also brings challenges to the radio operator concerning receiver “noise” levels, RF interference from adjacent sources including close by transmitting stations, and RFI from portable generators.  A typical scenario and some suggested Palomar product solutions are shown in the picture below:

Generator RFI testimonial:

Bob 

Received your order in a timely fashion. Tried the generator kit on Sunday & it drops the noise from S9 to S5 and 
took out all the electrical noise.  I may want some more toroids from you at some point for other interference problems
I have  here.
Ken VE3KCY

Using an amplifier?  Don’t forget our Linear Amplifier RFI Kits

Want to make up your own RFI kits for a particular operation? Here are links to some of  typical RFI solutions used in portable operations:

AC/DC common mode filters

Feed Line chokes

Coax Noise Filters

If you use a computer for logging in your portable operations, RFI getting into computers will often lock up your computer and/or radio and a computer RFI suppression kits may be helpful

Computer RFI Kits

Make your expedition or portable operation a pleasant and fun outing and remember to take along your RFI kits so you have more time to operate rather then to troubleshoot intermittent or noisy receiver conditions.

Portable Antenna Kits

If you need an effective portable antenna which folds up for transport yet is easy to deploy at your operating site, consider the BULLET series of end fed wire antennas.

BULLET Antennas (click on link or picture for more info)

Bullet Antenna Product 300x292 - Portable Operation RFI Kits