Home Theater RFI Kit

HF Transceiver RFI/Noise Reduction Kit, RFI Range 1-300 MHz, 5 Filters

SKU RFI-XCVR-STD
$39.95
Bulk pricing available for quantities of 2 units or more
1
Buy more, save more
QuantityPrice per itemDiscount
2 items$36.958% off
10 items$32.9518% off
100 items$29.9525% off
Save this product for later
Share this product with your friends
HF Transceiver RFI/Noise Reduction Kit, RFI Range 1-300 MHz, 5 Filters
Product Details
MPN: RFI-XCVR-STD
Type: NEW
Country/Region of Manufacture: United States
Filter Power Rating (PEP watts): 1500
RFI Suppression Range (MHz): 1-300 MHz
# Ferrite Filters: 5
Enclosure Size (inches): n/a
Typical Use:: AC/DC power, RF output, 3 I/O lines

BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH MANY BRANDS OF HAM/COMMERCIAL HF RADIOS

Standard Kit Includes noise reduction ring filters for coax, AC/DC power and 3 snap on filters for I/O cables covering RFI range of 1-300 MHz. Quick installation - immediate RFI/noise reduction. No radio mods required.

Use With all brands including:

Icom: IC-706, 718, 746. 756, 7100, 7200, 7300, 7400

Kenwood: TS-480

Yaesu: FT-450, 817/818, 857, 891, 897, 950, 991A, 1200


If you have a high end radio with multiple antennas, and more than 3 I/O cables, use our Deluxe Transceiver RFI Kit, RFI-XCVR-DELUXE

Purpose

The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and AC/DC power cable. Additional chokes are included to reduce common mode currents on 3 more transceiver cables including computer control, audio and another.

This kit will help reduce or eliminate:

1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.

2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.

3. RFI to your other radios, audio/video systems, computers, telephones, etc.

A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).

These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.

The snap on beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.

Use of the chokes often helps cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The AC/DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.

Included are the following chokes and installation guidelines:

RF Input/Output: 1.4" ID ring filter – 5-9 turns of RG-58/RG-8X size coax cable through center

AC/DC Input: 1.4" ID ring filter – 3-7 turns of AC/DC power cable through center

3 additional I/O cables - 1/2" snap on with 1-2 turns through center. Multiple wires can share the same filter.


For additional RFI suppression, use a feed line choke at the antenna feed point to suppress common current on the coax feed line.


If you use a linear amplifier use an amplifier RFI kit for additional RFI interference suppression.

TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices. If you run a high powered RF amplifier in your ham station also consider a linear amp RFI kit which will cut down RFI transmitted by your station. Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.

Typical RFI Problem/Solution:

Hello,
I am Larry, a ham operator and I am having interference issues with
my Direct TV system.
My station is a FT450D through an Ameritron ALS-600. From the amp
through a coax switch  to choose between an OCF dipole or an Hustler
5BTV vertical. Any power over 100 watts and my DTV goes off the air
and must completly reboot/format. Coax is RG-8. The DTV dish is
pointed away from the dipole and separated by about 25'. DTV was
totally useless! They suggested I not talk on the radio while she is
watching TV!  Please help me with a reasonable, cost effective
soultion. (The wife gets really pissed when I shutdown the tv!)

Thank you,

Larry 

 

Hi Larry,

Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.

The solutions are straight forward:

1. To make sure your feed line is not radiating you need a feed line choke at each antenna feed point (also makes your antenna work better since it is not using the coax as part of the antenna).  You can use our simple Kit 110 with 5 snap on chokes on each antenna for this purpose.  Part # Kit 110 at $27.50 each – one for each antenna.  These chokes will keep your feed line from radiating and coupling into your ac power lines.  INFO HERE

2. The radiation from your antennas themselves may also be getting into the ac power lines and coax braid of the Direct TV antenna so you need to protect the victim receiver.  Depending upon the sophistication of your direct TV setup (e.g. home theater, dvd, tape player, sub woofer speakers, etc), the path of the RFI may be coming thru the AC power lines of any connected device to the video including the video monitor itself!  To help solve this problem we have a home theater RFI kit for up to 5 devices (you need a minimum of two – one for the Direct TV receiver(AC and coax input) and another for the video monitor AC power lines and HDMI or video input cable.  Our kit part # is RFI-HTS.  INFO HERE

These items should help reduce the RFI and let you operate on the air while your wife watches TV.

Bob Brehm, AK6R

Chief Engineer