HF Transceiver RFI/Noise Reduction Kit - 5 Noise Reduction Filters + Coax Noise FilterProduct DetailsMPN: RFI-XCVR-STD+NFType: NEWCountry/Region of Manufacture: United StatesFilter Power Rating (PEP watts): = Cable RatingRFI Suppression Range (MHz): 1-300 MHz# Ferrite Filters: 5Enclosure Size (inches): n/aTypical Use:: AC/DC power, RF output, 3 additional I/O linesBUY THIS KIT NOW TO SOLVE YOUR RFI PROBLEMS! WORKS WITH MANY BRANDS OF HAM/COMMERCIAL HF RADIOS WITH SINGLE ANTENNA INPUT. This kit is an improvement over our standard HF transceiver RFI Kit and now includes our very effective Coax Noise Filter, (CMNF-500-50) to reduce common mode noise picked up by the antenna feed line coax as well as individual filters for the DC power line, and other cables including DIN Plug, Remote/CIV, AMP Send/ALC, and USB. (Note: if you have multiple antenna inputs, use a separate CMNF-500-50 on each HF coax line or a CMNF-500-50VHF for 144 or 450 MHz coax inputs).
This kit will help reduce or eliminate:
1. Radio Frequency Interference (RFI) to electronic devices including audio/video systems, computers, telephones, garage door openers, alarm systems, and home appliances, in your house or your neighbor’s house.
2. RFI from other electronic devices such as switching power supplies, LED and fluorescent lights, battery chargers, Ethernet cables, solar systems, kitchen appliances, and cable/satellite TV systems which generate common mode currents on your radio cables.
3. These filters help cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The DC power line filter helps keep common mode current out of the power line which could cause interference to other devices connected to the same power source.
These filters use a ferrite core material that is effective in suppressing RFI from transmitters and receivers experiencing a high noise floor in the 1-300 MHz range. DC filter effective for .15-10 MHZ and CMNF-500-50 effective from 1-60 MHz range. Snap on filters effective from 1-300 MHz.
The ferrite split beads and ring filters are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.
Kit Includes a low frequency noise reduction ring filter (works great on DC switching power supplies too!) for AC/DC power, 4 snap on filters (1/2" ID) for I/O cables and the CMNF-500-50 coax noise filter and double male barrel connector for direct attachment to your radio antenna connector. The CMNF-500-50 provides up to 38 dB (6 "S" units) of common mode noise attenuation. Snap on ferrites may be either 4 or 6 sided depending on inventory - they have identical electrical properties..
This Kit features Quick installation - immediate RFI/noise reduction. No radio mods required.
For additional RFI suppression, use a feed line choke (like the MC-1-500 for 500 watts or the MC-1-3000 for powers up to 3KW PEP) at the antenna feed point to suppress common current on the coax feed line during TRANSMIT.
If you use a linear amplifier use a Palomar Engineers Amplifier RFI kit (part# RFI-LA-GAC) for additional RFI interference suppression.
Icom 7300 RFI Kit Flyer Download (not available on eBay)
On Sale
Laptop Computer with DC power RFI Kit - 7 FiltersLaptop Computer with DC power RFI Kit - 7 FiltersSKU RFI-LaptopList price $34.95 Save 14%$29.95On Sale
Desktop Computer with AC power RFI Kit - 7 FiltersDesktop Computer with AC power RFI Kit - 7 FiltersSKU RFI-DesktopList price $39.95 Save 25%$29.95On Sale
RG-8X Coax Jumper Cable with PL-259's on each end - 3 feetRG-8X Coax Jumper Cable with PL-259's on each end - 3 feetSKU RG-8X-3List price $19.95 Save 15%$16.95On Sale
Generic Computer Equipment/Ethernet RFI Kit - 10 FiltersGeneric Computer Equipment/Ethernet RFI Kit - 10 FiltersSKU RFI-COMPUTERList price $59.95 Save 17%$49.95
BUY THIS KIT NOW TO SOLVE YOUR RFI PROBLEMS! WORKS WITH MANY BRANDS OF HAM/COMMERCIAL HF RADIOS WITH SINGLE ANTENNA INPUT. This kit is an improvement over our standard HF transceiver RFI Kit and now includes our very effective Coax Noise Filter, (CMNF-500-50) to reduce common mode noise picked up by the antenna feed line coax as well as individual filters for the DC power line, and other cables including DIN Plug, Remote/CIV, AMP Send/ALC, and USB. (Note: if you have multiple antenna inputs, use a separate CMNF-500-50 on each HF coax line or a CMNF-500-50VHF for 144 or 450 MHz coax inputs).
This kit will help reduce or eliminate:
1. Radio Frequency Interference (RFI) to electronic devices including audio/video systems, computers, telephones, garage door openers, alarm systems, and home appliances, in your house or your neighbor’s house.
2. RFI from other electronic devices such as switching power supplies, LED and fluorescent lights, battery chargers, Ethernet cables, solar systems, kitchen appliances, and cable/satellite TV systems which generate common mode currents on your radio cables.
3. These filters help cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The DC power line filter helps keep common mode current out of the power line which could cause interference to other devices connected to the same power source.
These filters use a ferrite core material that is effective in suppressing RFI from transmitters and receivers experiencing a high noise floor in the 1-300 MHz range. DC filter effective for .15-10 MHZ and CMNF-500-50 effective from 1-60 MHz range. Snap on filters effective from 1-300 MHz.
The ferrite split beads and ring filters are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.
Kit Includes a low frequency noise reduction ring filter (works great on DC switching power supplies too!) for AC/DC power, 4 snap on filters (1/2" ID) for I/O cables and the CMNF-500-50 coax noise filter and double male barrel connector for direct attachment to your radio antenna connector. The CMNF-500-50 provides up to 38 dB (6 "S" units) of common mode noise attenuation. Snap on ferrites may be either 4 or 6 sided depending on inventory - they have identical electrical properties..
This Kit features Quick installation - immediate RFI/noise reduction. No radio mods required.
For additional RFI suppression, use a feed line choke (like the MC-1-500 for 500 watts or the MC-1-3000 for powers up to 3KW PEP) at the antenna feed point to suppress common current on the coax feed line during TRANSMIT.
If you use a linear amplifier use a Palomar Engineers Amplifier RFI kit (part# RFI-LA-GAC) for additional RFI interference suppression.
Icom 7300 RFI Kit Flyer Download (not available on eBay)
TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices. If you run a high powered RF amplifier in your ham station also consider a linear amp RFI kit which will cut down RFI transmitted by your station. Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.
Typical RFI Problem/Solution:
Hello, I am Larry, a ham operator and I am having interference issues with my Direct TV system. My station is a FT450D through an Ameritron ALS-600. From the amp through a coax switch to choose between an OCF dipole or an Hustler 5BTV vertical. Any power over 100 watts and my DTV goes off the air and must completly reboot/format. Coax is RG-8. The DTV dish is pointed away from the dipole and separated by about 25'. DTV was totally useless! They suggested I not talk on the radio while she is watching TV! Please help me with a reasonable, cost effective soultion. (The wife gets really pissed when I shutdown the tv!) Thank you, Larry
Hi Larry,
Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.
The solutions are straight forward:
1. To make sure your feed line is not radiating you need a feed line choke at each antenna feed point (also makes your antenna work better since it is not using the coax as part of the antenna). You can use our simple Kit 110 with 5 snap on chokes on each antenna for this purpose. Part # Kit 110 at $27.50 each – one for each antenna. These chokes will keep your feed line from radiating and coupling into your ac power lines. INFO HERE
2. The radiation from your antennas themselves may also be getting into the ac power lines and coax braid of the Direct TV antenna so you need to protect the victim receiver. Depending upon the sophistication of your direct TV setup (e.g. home theater, dvd, tape player, sub woofer speakers, etc), the path of the RFI may be coming thru the AC power lines of any connected device to the video including the video monitor itself! To help solve this problem we have a home theater RFI kit for up to 5 devices (you need a minimum of two – one for the Direct TV receiver(AC and coax input) and another for the video monitor AC power lines and HDMI or video input cable. Our kit part # is RFI-HTS. INFO HERE
These items should help reduce the RFI and let you operate on the air while your wife watches TV.
Bob Brehm, AK6R
Chief Engineer