50:450 ohm (9:1) Balun or Unun Core Kit, .5-32 MHz, 1000 watts PEP, end fed/Ladder Line, T2FD antennaProduct DetailsMPN: BA-9-1000Type: balun or ununInput ohms/Output ohms: 50 in, 450 outFrequency Range < 2:1 SWR (MHz): .5-32PEP Power Rating (watts): 1000 Watts PEPAntenna Compatability: Unun: End fed, Balun: Ladder linePurpose. Model BA-9-1000 is a 9:1 balun/unun kit (assembly required from parts supplied) used to translate a 50 ohm input up to 450 ohms at RF power levels up to 1000 watts when used with a matched load. It provides conversion from unbalanced coax to balanced ladder line/antenna feed point and gives a 9:1 impedance step-up to reduce SWR on the coax. Place at the junction of the balanced line and the coax to convert from balanced line to unbalanced coax.It can also be wired as an UNUN with unbalanced coax input to unbalanced output such as an end fed antenna.
KIT Contents. The kit consists of a F240-61 ferrite toroidal core, three colors of insulated wire, a SO-239 UHF connector with stainless steel hardware, and an instruction manual.
Assembly time: About 1 hour
Radio Club idea:
Buy 10 for a club do it yourself construction project - you can learn something and also build an end fed antenna (just add wire).
Purpose. Model BA-9-1000 is a 9:1 balun/unun kit (assembly required from parts supplied) used to translate a 50 ohm input up to 450 ohms at RF power levels up to 1000 watts when used with a matched load. It provides conversion from unbalanced coax to balanced ladder line/antenna feed point and gives a 9:1 impedance step-up to reduce SWR on the coax. Place at the junction of the balanced line and the coax to convert from balanced line to unbalanced coax.It can also be wired as an UNUN with unbalanced coax input to unbalanced output such as an end fed antenna.
KIT Contents. The kit consists of a F240-61 ferrite toroidal core, three colors of insulated wire, a SO-239 UHF connector with stainless steel hardware, and an instruction manual.
Assembly time: About 1 hour
Radio Club idea:
Buy 10 for a club do it yourself construction project - you can learn something and also build an end fed antenna (just add wire).
TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices. If you run a high powered RF amplifier in your ham station also consider a linear amp RFI kit which will cut down RFI transmitted by your station. Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.
Typical RFI Problem/Solution:
Hello, I am Larry, a ham operator and I am having interference issues with my Direct TV system. My station is a FT450D through an Ameritron ALS-600. From the amp through a coax switch to choose between an OCF dipole or an Hustler 5BTV vertical. Any power over 100 watts and my DTV goes off the air and must completly reboot/format. Coax is RG-8. The DTV dish is pointed away from the dipole and separated by about 25'. DTV was totally useless! They suggested I not talk on the radio while she is watching TV! Please help me with a reasonable, cost effective soultion. (The wife gets really pissed when I shutdown the tv!) Thank you, Larry
Hi Larry,
Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.
The solutions are straight forward:
1. To make sure your feed line is not radiating you need a feed line choke at each antenna feed point (also makes your antenna work better since it is not using the coax as part of the antenna). You can use our simple Kit 110 with 5 snap on chokes on each antenna for this purpose. Part # Kit 110 at $27.50 each – one for each antenna. These chokes will keep your feed line from radiating and coupling into your ac power lines. INFO HERE
2. The radiation from your antennas themselves may also be getting into the ac power lines and coax braid of the Direct TV antenna so you need to protect the victim receiver. Depending upon the sophistication of your direct TV setup (e.g. home theater, dvd, tape player, sub woofer speakers, etc), the path of the RFI may be coming thru the AC power lines of any connected device to the video including the video monitor itself! To help solve this problem we have a home theater RFI kit for up to 5 devices (you need a minimum of two – one for the Direct TV receiver(AC and coax input) and another for the video monitor AC power lines and HDMI or video input cable. Our kit part # is RFI-HTS. INFO HERE
These items should help reduce the RFI and let you operate on the air while your wife watches TV.
Bob Brehm, AK6R
Chief Engineer