AM Broadcast RFI Kits

RFI Common Mode Noise Filter Kits for Generic Antenna Switches - Isolate Non-Selected Coax Braid Noise!

Suppress Unwanted Noise & RFI
SKU RFI-AS-GEN-2
$129.95
Filter Max Power (PEP)
Antenna Ports
1
Save this product for later
Share this product with your friends
RFI Common Mode Noise Filter Kits for Generic Antenna Switches - Isolate Non-Selected Coax Braid Noise!
Product Details

Coax antenna switches generally only switch the center conductor of the coax and all the coax braids remain connected in parallel summing the common mode noise off ALL coax lines onto the coax selected - this means you may be picking up common mode noise from coax lines that are not even connected to the coax antenna selected. The only practical solution is to isolate the coax braids from each other BEFORE they connect to the antenna switch as shown in the picture for a simple 2 position antenna switch.

This product listing is for use with your antenna switches which have 2 - 8 antennas. Each switched line needs a common mode noise filter prior to being connected to the switch. In some cases you can use a double male barrel connector to attach the filter to the switch or you may need a short jumper cable. (ANTENNA SWITCH SHOWN IN PICTURE NOT INCLUDED - SHOWN FOR ILLUSTRATION OF USE ONLY)

We offer a low power filter (CMNF-500-50 up to 500 watts PEP and up to 46 dB of common mode noise suppression per line) or a high power (Maxi-Choker, MC-1-3000 up to 3KW PEP and up to 60 dB of common mode noise suppression per line) and 2-8 ports of antenna switch. If you use a dummy load for one of the switched ports you do not need a filter for that port. Each filter has a range of 1.8 to 61 MHz (see individual listing on this website for specifics).


When considering solutions for AM broadcast (550 Khz – 1.8 Mhz) you should consider Mix 77 ferrites available in a variety of shapes and sizes.  Choose a size to give the maximum number of turns of the affected wire or cable.

AM broadcast transmits on a low frequency with large antennas.  Consequently it takes a large antenna to receive the signals.  Typical “antennas” are AC house wiring, phone lines, long satellite or cable TV cables, DSL/CAT5 lines running between rooms, etc.  The device wires that connect to these  “antennas” need to be choked with as many turns through the ferrite as possible.  Some installation examples are shown below on this page.

For AC/ DC power cords and coax cables the F240-77 (2.4″ OD, 1.4″ ID) “Donut” toroid is the most popular.  Also available are smaller toroid donuts and Mix 77 beads. Shown below is a graph with 8, 10, and 12 turns through the toroid – obviously more turns has higher choking impedance.  Mix 77 toroid products are HERE and Mix 77 small beads (for small wires) are HERE

F240 77 Turns Comparison 1024x648 - AM Broadcast RFI Kits

F240-77 Turns Comparison from .1 – 8.1 Mhz

Shown below is a graph of frequency response verses choking magnitude for a F240-77 in the AM Broadcast band for a 12 turn coil around the toroid. (Same info as above but different frequency range).

AM Band Choking Graph F240 77 1024x648 - AM Broadcast RFI Kits

F240-77 Choking Impedance in AM Broadcast Band

 

 

Typical Installations for Donut/Ring Toroids

20131210 114716 150x150 - AM Broadcast RFI Kits

AC Cable on F-240 Toroid – 6 turns

20131210 115137 150x150 - AM Broadcast RFI Kits

Ethernet Cable on F-240 Toroid – 7 turns

20131222 125533 150x150 - AM Broadcast RFI Kits

Audio or Mic cable on F240- 12 turns

 

 Extra Mix 75 Snap On Beads  HERE – VERY effective for AM Broadcast RFI