AM Broadcast RFI Kits

End Fed Feed Line Choke for Non-Resonant and End Fed Half Wave Antennas

SKU EFFLC-240
$10.00
Bulk pricing available for quantities of 10 units or more
1
Buy more, save more
QuantityPrice per itemDiscount
10 items$9.0010% off
Save this product for later
Share this product with your friends
End Fed Feed Line Choke for Non-Resonant and End Fed Half Wave Antennas
Product Details
Type: 8-10 turns of RG-8X with Pl259 Connector, 3 turns of RG-213 cable
RFI Range (MHz): 1-300 MHz
ID-B (in/mm): 1.4"
OD-A (in/mm): 2.4"
Height-C (in/mm): 1/2"

Feed Line Choke

Each end fed antenna needs a feed line
choke at the radio end of the coax to stop the antenna common mode
current (on the coax braid) from getting into the radio when
transmitting and also to stop RFI common mode noise when receiving. The
simplest, most cost effective choke is a ferrite ring (F240 size)
installed as shown in the picture (at the transceiver end of the coax)

Add the Feed line choke (part # EFFLC-240) for $10 to your end fed
today and stop the pesky RFI from getting into your radio and causing
audio distortion or unexpected operation!


NOTE: Coax shown in picture is NOT INCLUDED and is shown as an installation example only. If you want a pre-wound choke check part# JC-1-1500-3 or JC-1-1500-6.


For non-resonant end fed antennas placement of the choke from 16-95 feet away from the antenna feed point to use the coax braid as the counterpoise (since these antennas are really off center fed dipoles with the short side using the coax braid as the counterpoise. Wind 8-10 turns thru center for an effective 3-30 MHz choke. See Bullet Antenna configurations for exact choke placement depending upon wire length.


For End fed Half Wave antennas place 1-3 feet from antenna feed point to act as short counterpoise for these voltage fed antennas. Use 8-10 turns.

When considering solutions for AM broadcast (550 Khz – 1.8 Mhz) you should consider Mix 77 ferrites available in a variety of shapes and sizes.  Choose a size to give the maximum number of turns of the affected wire or cable.

AM broadcast transmits on a low frequency with large antennas.  Consequently it takes a large antenna to receive the signals.  Typical “antennas” are AC house wiring, phone lines, long satellite or cable TV cables, DSL/CAT5 lines running between rooms, etc.  The device wires that connect to these  “antennas” need to be choked with as many turns through the ferrite as possible.  Some installation examples are shown below on this page.

For AC/ DC power cords and coax cables the F240-77 (2.4″ OD, 1.4″ ID) “Donut” toroid is the most popular.  Also available are smaller toroid donuts and Mix 77 beads. Shown below is a graph with 8, 10, and 12 turns through the toroid – obviously more turns has higher choking impedance.  Mix 77 toroid products are HERE and Mix 77 small beads (for small wires) are HERE

F240 77 Turns Comparison 1024x648 - AM Broadcast RFI Kits

F240-77 Turns Comparison from .1 – 8.1 Mhz

Shown below is a graph of frequency response verses choking magnitude for a F240-77 in the AM Broadcast band for a 12 turn coil around the toroid. (Same info as above but different frequency range).

AM Band Choking Graph F240 77 1024x648 - AM Broadcast RFI Kits

F240-77 Choking Impedance in AM Broadcast Band

 

 

Typical Installations for Donut/Ring Toroids

20131210 114716 150x150 - AM Broadcast RFI Kits

AC Cable on F-240 Toroid – 6 turns

20131210 115137 150x150 - AM Broadcast RFI Kits

Ethernet Cable on F-240 Toroid – 7 turns

20131222 125533 150x150 - AM Broadcast RFI Kits

Audio or Mic cable on F240- 12 turns

 

 Extra Mix 75 Snap On Beads  HERE – VERY effective for AM Broadcast RFI