Off Center Fed (OCF) Dipole Baluns

MINI-BALUN 4:1 Coax Interface to Ladder Line, Loop, OCF antennas 500 Watts PEP, 1-61 MHz

SKU MB-4-500SS
$69.95
Bulk pricing available for quantities of 2 units or more
1
Buy more, save more
QuantityPrice per itemDiscount
2 items$64.957% off
10 items$59.9514% off
Save this product for later
Customer reviews
No reviews yet. Only signed-in customers who bought this product can leave reviews. To leave a review, sign in
Share this product with your friends
MINI-BALUN 4:1 Coax Interface to Ladder Line, Loop, OCF antennas 500 Watts PEP, 1-61 MHz
Product Details
Brand: Palomar Engineers
MPN: MB-4-500TS
Country/Region of Manufacture: United States
Effective Frequency Range (MHz): 1-60
PEP Power Rating (watts): 500 SSB (25% duty cycle), 250 Watts CW/FT8 (50% duty cycle)
Estimated Insertion Loss (db): .25 db
Input Connector Type: SO-239 female
Output Connector Connector Type: Dual 1/4" stainless steel studs
Enclosure Size (LxWxH inches): 3" long, 2 in wide, 1.25" high

MINI-BALUN Features:

- Uses proprietary Multi-Turn, Multi-Ferrite technology for maximum power transfer and minimum SWR

- 500 Watts PEP, 50 ohm SO-239 connectors In, Dual Side Stud Output, 1-61 MHz (usable to 100 MHz) - AKA 4:1 BALUN

- Works for coax fed antennas from 1.8-61 MHz (160-6 meters) - excellent for multi-band loops, OCF, G5RV/ZS6BKW or Flag Pole OCF antennas fed with ladder line.

- 2-5 times more wider bandwidth and higher power then competing baluns of similar power ratings


This balun has a SO-239 input and 1/4" side studs output.

For Higher Power needs use our CB-4-1500TS or CB-4-5000TS







Testimonial

Hi Bob,

Radio: Flex-6700 running barefoot -10 to 100 Watts max.
Antenna: MFJ-1216 – 160/80 meter OCFD wire antenna with matching network.
Elevation: Over 60 feet AGL – fully extended.
Installed: Mid November 2013

I operate mainly on the digital modes running less than 50 Watts.  All of the sudden after a few days operating with this antenna, I start to have RFI and my radio was acting up; such as changing bands, SWR changing values, radio failures and turning off. However, when I used my Hy-Gain 18 HT vertical on the same band none of the abnormality occurred.
I contacted MFJ and confirm that what I was noticing was a failure of their “matching network” AKA balun.  They offered no solutions. Then I contacted Palomar Engineers and bought the 1:1 new toroid RF beads.  I called Palomar Engineers and I happened to talked to you directly; regarding the on going issue with the MFJ antenna. I found out that the 1:1 balun was not what I needed (I was miss-informed by MFJ that it was 1:1 matching network.)
You offered to make the required balun 4:1 and the rest is history.

Here are my findings:

  1. No more RFI displayed on the monitors.
  2. Radio not acting up or turning off.
  3. The SWR at 160/80 meter is 1.2:1
  4. No antenna tuner required.  (radio goes to Bypass automatically.)
  5. Worst SWR is on 10 meter with a 2:1 but still usable, with antenna tuner 1.5.
  6. One happy OCFD user!

Thanks to Palomar Engineers design and engineering for solving this issue.

73, Ernest – W4EG