Wall Wart RFI Noise Filter

Snap On RF Choke/Isolator - 3/8"/9mm cable, 5/10/15 Bead Option, 1-300 MHz

SNO-3/8-5
$17.95
In stock
1
Product Details
Brand: Palomar Engineers
MPN: SNO-3/8-5
Effective Frequency Range (MHz): 3-300
PEP Power Rating (watts): same as coax cable rating
Choking Impedance Range (ohms): 5 bead: 500-100, 10 bead: 600-1800, 15 bead: 1000-2100
Common Mode Attenuation (db): 5 bead: 16-22db, 10 bead: 17-25db, 15 bead: 21-27 db
Estimated Insertion Loss (db): .025
Input Connector Type: none
Output Connector Connector Type: none
Ground Connector (Y/N): none
Enclosure Size (LxWxH inches): none

Use for 3/8″ Cable – RG-8X, LMR-240, etc

For 3/8” cables use five FSB31-3/8 split beads for 80-10 meters (3-30 mHz) or ten FSB-3/8 split beads for 160-10 (1.8-30 MHz) meters or use 15 FSB31-3/8 for even higher choking for 1-10 MHz.

Typical Impedance per split bead: 10 MHz: 100 ohms, 25 MHz: 163 ohms, 100 MHz: 275 ohms, 250 MHz: 275 ohm

Minimum recommended total impedance is 500 ohms at frequency of interest.

The beads clamp to the cable and may be operated as is for indoor use. However, it is strongly suggested that they be covered to protect the plastic covers from weathering – use electrical tape for best results or heat shrink to ensure longer life. All kits come with instruction manual which covers assembly and application tips.

As you can see from the impedance vs frequency graph, you can very effectively increase the choking impedance by increasing the number of beads on the cable.

Save this product for later
Wall Wart switching DC power supplies that plug into the AC power line plug and provide DC power to laptops, routers, battery chargers, cell phone chargers, etc are a known source of broadband RFI (a.k.a dirty electricity) that effects many electrical devices including computers, radio receivers, HDTV systems, etc.  In many cases this extra RFI noise effects computer I/O speeds since they have to error correct the information packets many more times due to the noise interference causing packet errors.  A ferrite ring can often increase data throughput by reducing the error correction to normal rates.

A simple ferrite ring filter on the DC power line can help suppress the RFI noise affecting the victim device or keep the DC power cord from acting as an antenna and radiating RFI into other victim devices. This kit is also useful on laptop computer supplies, routers, cable modems, wireless phone charges, etc.

RFI WW Installation 300x288 - Wall Wart RFI Noise Filter

Installation is quick and easy: Just wrap the DC power cord through the center of the ring filter as many times as you can and reinstall.  For best results with long DC power lines, use one at the ring filter at the wall wart end (to prevent the wall wart power supply from using the DC line as an antenna) and another at the DC plug end (to prevent the electronics in the powered device from using the DC power cord as an antenna).  Typical installation is shown below:

The filter suppresses RFI in from .1-100 MHz.   Inside diameter is 3/4 inch/19 mm.

Since most households and office environments have multiple wall warts we offer the Wall Wart RFI Filter kit in bulk quantity packages.

Known RFI Generators include Roku/Sling-TV power adapter - Interference heard in the AM broadcast band
 and harmonics.
Also many ethernet Cable/DSL modems, cell phone chargers, computer power adapters have the same issue:
using the AC or DC side of the power supply as a radiating antenna.

RFI solution is to use a linear power supply, change adapters or wall wart ferrite filters