Wall Wart RFI Noise Filter

982808126 - Wall Wart RFI Noise Filter
+3

Home Theater System RFI Kit for up to 4 HDTV, A/V units + I/O cables - 12 filters

RFI-HTS
$69.95
In stock
1
Product Details
MPN: RFI-HTS
Type: NEW
Country/Region of Manufacture: USA
Filter Power Rating (PEP watts): not applicable
RFI Suppression Range (MHz): 1-300 MHz

The RFI-HTS kit is specifically designed to cure most home theater/audio/video systems triggered by Radio Frequency Interference problems generated by AM/FM, CB and Ham radio transmitters or other consumer electronic devices. The ferrite filters are selected to eliminate RFI from 1 to 300 MHz. The ferrites are easy to use, don’t require modification of the protected equipment and work in almost all cases.

What is included in the kit?

The RFI-HTS kit contains a selection of ferrites for 4 AC powered units such as cable/satellite box, HDTV, amplifier system, DVD/BlueRay player and powered sub-woofer. RFI at lower frequencies typically comes through the AC power lines acting as “antennas” picking up the interference signal and these ferrite compositions have been specifically selected to suppress this interference. Also included are snap-on ferrites in 1/2" (4) and 3/8″ (4) hole size to accommodate various interconnect and speaker wires. An instruction sheet is included with typical installation examples.

TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices.Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.

Typical RFI Problem/Solution:

Hello,
I am Larry, a ham operator and I am having interference issues with
my Direct TV system.
My station is a FT450D through an Ameritron ALS-600. From the amp
through a coax switch to choose between an OCF dipole or an Hustler
5BTV vertical. Any power over 100 watts and my DTV goes off the air
and must completely reboot/format. Coax is RG-8. The DTV dish is
pointed away from the dipole and separated by about 25'. DTV was
totally useless! They suggested I not talk on the radio while she is
watching TV! Please help me with a reasonable, cost effective
soultion. (The wife gets really pissed when I shutdown the tv!)
Thank you,
Larry

Hi Larry,

Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.

The solutions are straight forward using our home theater system RFI kit.

Save this product for later
Display prices in: USD
Wall Wart switching DC power supplies that plug into the AC power line plug and provide DC power to laptops, routers, battery chargers, cell phone chargers, etc are a known source of broadband RFI (a.k.a dirty electricity) that effects many electrical devices including computers, radio receivers, HDTV systems, etc.  In many cases this extra RFI noise effects computer I/O speeds since they have to error correct the information packets many more times due to the noise interference causing packet errors.  A ferrite ring can often increase data throughput by reducing the error correction to normal rates.

A simple ferrite ring filter on the DC power line can help suppress the RFI noise affecting the victim device or keep the DC power cord from acting as an antenna and radiating RFI into other victim devices. This kit is also useful on laptop computer supplies, routers, cable modems, wireless phone charges, etc.

RFI WW Installation 300x288 - Wall Wart RFI Noise Filter

Installation is quick and easy: Just wrap the DC power cord through the center of the ring filter as many times as you can and reinstall.  For best results with long DC power lines, use one at the ring filter at the wall wart end (to prevent the wall wart power supply from using the DC line as an antenna) and another at the DC plug end (to prevent the electronics in the powered device from using the DC power cord as an antenna).  Typical installation is shown below:

The filter suppresses RFI in from .1-100 MHz.   Inside diameter is 3/4 inch/19 mm.

Since most households and office environments have multiple wall warts we offer the Wall Wart RFI Filter kit in bulk quantity packages.

Known RFI Generators include Roku/Sling-TV power adapter - Interference heard in the AM broadcast band
 and harmonics.
Also many ethernet Cable/DSL modems, cell phone chargers, computer power adapters have the same issue:
using the AC or DC side of the power supply as a radiating antenna.

RFI solution is to use a linear power supply, change adapters or wall wart ferrite filters