AM Broadcast RFI Kits

MAXI-CHOKER Coax Line Isolator/Balun, 1-61 MHz, 3KW, SO-239 In/Stud Output, G5RV/ZS6BKW Replacement

SKU MC-1-3000LL
$89.95
In stock
1
Product Details

MAXI-CHOKER Features:

- Uses proprietary Multi-Mix(TM) technology for maximum choking (up to 5K ohm) and maximum bandwidth

- 3 KW PEP, 50 ohm SO-239 connectors In dual screw terminal output for ladder line, 1-61 MHz

- Hi choking resistance solves tough RFI issues

- Works for all coax fed antennas from 1.8-61 MHz (160-6 meters) - excellent for multi-band beams, verticals, dipoles and off center fed antennas.

- 2-5 times more choking resistance, wider bandwidth and higher power then competing filters

- great replacement choke for G5RV/ZS6BKW antennas or as a 1:1 ladder line to coax interface with high common mode choking to isolate the coax braid from becoming part of the antenna.

- Available with ground lug/internal static bleeder option


MAXI-CHOKER feed line chokes are used to suppress common mode current carried on the outside of the coax braid which is often responsible for receiver noise and RFI in the receiver/transmitter. These chokes are very useful for suppressing RFI common mode current at the antenna feed point or at a ladder line to coax junction, like a G5RV antenna.

Note: Color may be white or black depending on on inventory at time of order. Ladder Line shown NOT included.





Save this product for later
When considering solutions for AM broadcast (550 Khz – 1.8 Mhz) you should consider Mix 77 ferrites available in a variety of shapes and sizes.  Choose a size to give the maximum number of turns of the affected wire or cable.

AM broadcast transmits on a low frequency with large antennas.  Consequently it takes a large antenna to receive the signals.  Typical “antennas” are AC house wiring, phone lines, long satellite or cable TV cables, DSL/CAT5 lines running between rooms, etc.  The device wires that connect to these  “antennas” need to be choked with as many turns through the ferrite as possible.  Some installation examples are shown below on this page.

For AC/ DC power cords and coax cables the F240-77 (2.4″ OD, 1.4″ ID) “Donut” toroid is the most popular.  Also available are smaller toroid donuts and Mix 77 beads. Shown below is a graph with 8, 10, and 12 turns through the toroid – obviously more turns has higher choking impedance.  Mix 77 toroid products are HERE and Mix 77 small beads (for small wires) are HERE

F240-77 Turns Comparison from .1 - 8.1 Mhz

F240-77 Turns Comparison from .1 – 8.1 Mhz

Shown below is a graph of frequency response verses choking magnitude for a F240-77 in the AM Broadcast band for a 12 turn coil around the toroid. (Same info as above but different frequency range).

F240-77 Choking Impedance in Am Broadcast Band

F240-77 Choking Impedance in AM Broadcast Band

 

 

Typical Installations for Donut/Ring Toroids

AC Cable on F-240 Toroid - 6 turns

AC Cable on F-240 Toroid – 6 turns

Ethernet Cable on F-240 Toroid - 7 turns

Ethernet Cable on F-240 Toroid – 7 turns

RG58 12 turns on FT240-43 for 4000-6000 ohms choking impedance

Audio or Mic cable on F240- 12 turns

 

 Extra Mix 75 Snap On Beads  HERE – VERY effective for AM Broadcast RFI