Iron Powder Cores

50:100 (2:1) CUBE™ Balun/Unun 1.8-61 MHz, 2KW/5KW, Loop Antennas

CB-2-2000EB
$119.95
In stock
1
Product Details
Country/Region of Manufacture: USA
Type: BALUN or UNUN
Input ohms/Output ohms: 50
Frequency Range < 2:1 SWR (MHz): 1.8-61
PEP Power Rating (watts): 2000/5000
Enclosure Size: 4" x 4" x 2"
Weight (pounds): 3
Antenna Compatability: loops, quads, 100 ohm input antennas

High Power rated at 2KW/5KW (option) PEP (FT8 mode at 1.5KW for 5KW PEP model)

Broad frequency range of 1.8-61 MHz for < 2:1 SWR into matched load. 5KW model is 1.8-31 MHz

Compact 4" x 4" x 2" (2KW) or 4" x 4" x 2" (5KW) light weight weatherproof enclosure

Quick, easy deployment with either halyard hoist or side mounting tabs

Choice of BALUN (balanced outputs) or UNUN (unbalanced output and ground)

Model CB-2-2000 is a 2:1 (100:50) quad core balun used to translate a 50 ohm input to 100 ohms at RF power levels up to 2000 watts PEP when used with a matched load such as single band delta loop, quad or loop skywire. This assembled balun features a multi-core configuration for increased power handling and flatter frequency response to over 60 MHz. With a matched 100 ohm load the SWR over the frequency range is very consistent from 1.8-61 MHz and SWR is less than 2:1 over the range allowing easy tuning by most radio internal antenna tuners or an external tuner.

Save this product for later
IRON POWDER TOROID CORES-xx

Iron Cores 150x150 - Iron Powder CoresIron powder cores are more stable than ferrites and do not saturate as easily so they are best for tuned circuits, filters, and high power inductors. They come in different “Mixes” for use at different frequencies. For best “Q” use the Mix specified for your frequency.To find the number of turns to give the desired inductance for your coil use the formula below:

 

Turns = 100 x iron core formula 300x14 - Iron Powder Cores

Toroid Dimensions

tcolorcode - Iron Powder Corestcore - Iron Powder Cores

 

To order specify core size and mix (e.g. T200A-2). Available in sizes that have µH per 100 turns shown in table.

All iron powder cores are special orders.  Please allow one week for shipment after order received.

The iron powder cores shown in the above tables are primarily used for either high power feed line chokes for common mode current reduction or for 4:1  and 9;1 very high power transmission line transformers.

For high power feed line chokes, choose the inside diameter of the iron powder core closest to the transmission line outside diameter and use 6-20 cores at the junction with the antenna feed.

For 4:1 (50/200 or 75/300 ohm) transmission line transformers in the range of 1.8-30 Mhz, select the size appropriate for the power level as follows:

T200A x 2 = 1.5KW

T300A x 2 = 2.5KW

T400A x 2 = 5KW

Use Mix 2 for all the above transmission line transformers.  Fully assembled and enclosed units are available for each of the power levels.  Click HERE for information.

4:1 transmission line transformers using iron powder cores are typically used for ladder line to 50 ohm coax connections

For .1 – 2 Mhz wide band transformers use Mix 26 which has a higher permeability and requires less turns to achieve a given inductance. Mix 2 has almost constant permeability from 1-30 Mhz.  Mix 26 has an initial permeability of 75 at .1 Mhz and gradually decreases to about 10 at 30 Mhz.  For high power AM broadcast range (.5-1.7 Mhz) transformer, use Mix 26 to reduce the turn count.

Minimum order for iron powder cores is $50  

Shipping on larger cores in quantity may be more than $10 – email/call for quote.