Off Center Fed (OCF) Dipole Baluns

1725390966 - Off Center Fed (OCF) Dipole Baluns
+3

Hybrid 4:1 Balun + 1:1 Current Balun in one enclosure, 1.8-61 MHz, 1.5/5KW PEP - Loop, OCF Antennas

CB-4-1-1500EB
$139.95
In stock
1
Product Details
MPN: CB-4-1-1500TS/EB , CB-4-1-5000TS/EB
Country/Region of Manufacture: USA
Input ohms/Output ohms: 50 in/200 out
Frequency Range < 2:1 SWR (MHz): 1.8-61 MHz for 1.5KW
PEP Power Rating (watts): 1.5KW/5KW
Input Connector: UHF SO-239
Output Connector(s): Side Eyeboplts (EB) or Top Studs (TS)
Enclosure Size: 4"x4"x 2"(1.5KW), 4"x 4" x 4"(5KW)
Weight (pounds): 2# (1.5KW), 4# (5KW)
Antenna Compatability: OCF, Loop, BBTD, T2FD, ZEPP


After many requests we have created a compact, special balun for Off Center Fed (OCF) , loop (Skyloop or Delta loop) , BBTD, T2FD, folded dipoles antennas. The CB-4-1-1500 is a CUBE(TM) enclosure containing a multi-core, broadband 4:1 impedance transformer in series with a 1:1 current balun for extra common mode current choking to keep RF current off the outside of the coax braid and on the antenna where it belongs. The extra choking action also means that the coax feed line will not act as a radiator causing unnecessary RF interference (RFI). Rated for full 1500 watts PEP and 1000 watts CW (ICAS). 1.8Mhz – 61 MHz.

CB-4-1-1500 is housed in a 4” x 4” x 2” waterproof housing with SO-239 input and stainless steel eye bolts on the side for ease of connection to your wire antenna. Top eye bolt acts as an antenna hoist.

5KW are in 4" x 4" x 4" enclosure. 1.5KW is 2 pounds, 5KW is 4 pounds.

For an 80 meter OCF antennas we recommend a (95 feet/79.5% and 40 feet/29.5% offset for best all band results. If you use 66%/34% offset, do not use on 15 meters as the impedance mismatch may damage the balun at high power levels. Loop antennas should be cut for 1005/F(MHz) in total length, where F (MHz) is the lowest frequency to be used. For 3.5MHz this equates to 288 feet.

We highly recommend a feed line choke (MC-1-3000) or coax noise filter (CMNF-1500) at the radio end of the coax feed line to reduce common mode noise picked up by the coax braid.

CB-4-1-5000EB/TS are custom made to order - please allow 7-10 days ARO before ship.

Customer testimonial:

Callsign: NE5U Your CB-4-1500 +1:1 Choke made my homebrew, hail mary, 3 times folded 75m resonant attic dipole into a functional antenna from 6m to 160m. Most bands I can operate with no RFI. I've installed ferrites at all of the usual locations but still have some problem bands. Considering that the antenna is, at best, an NVIS antenna, I have made a lot of DX contacts (SSB, FT8 and other digital modes, and CW). Happy customer here. 73

Save this product for later
Display prices in: USD

Testimonial

Hi Bob,

Radio: Flex-6700 running barefoot -10 to 100 Watts max.
Antenna: MFJ-1216 – 160/80 meter OCFD wire antenna with matching network.
Elevation: Over 60 feet AGL – fully extended.
Installed: Mid November 2013

I operate mainly on the digital modes running less than 50 Watts.  All of the sudden after a few days operating with this antenna, I start to have RFI and my radio was acting up; such as changing bands, SWR changing values, radio failures and turning off. However, when I used my Hy-Gain 18 HT vertical on the same band none of the abnormality occurred.
I contacted MFJ and confirm that what I was noticing was a failure of their “matching network” AKA balun.  They offered no solutions. Then I contacted Palomar Engineers and bought the 1:1 new toroid RF beads.  I called Palomar Engineers and I happened to talked to you directly; regarding the on going issue with the MFJ antenna. I found out that the 1:1 balun was not what I needed (I was miss-informed by MFJ that it was 1:1 matching network.)
You offered to make the required balun 4:1 and the rest is history.

Here are my findings:

  1. No more RFI displayed on the monitors.
  2. Radio not acting up or turning off.
  3. The SWR at 160/80 meter is 1.2:1
  4. No antenna tuner required.  (radio goes to Bypass automatically.)
  5. Worst SWR is on 10 meter with a 2:1 but still usable, with antenna tuner 1.5.
  6. One happy OCFD user!

Thanks to Palomar Engineers design and engineering for solving this issue.

73, Ernest – W4EG