SUPER CHOKER™

Off Center Fed Dipole Antenna, 80-6 Meters (8 bands-including 15 meters), 500/1.5KW/5KW PEP rated - FREE shipping in USA

PAL-OCF8010-500
$169.95
In stock
1
Product Details
Brand: Palomar Engineers
Frequency Band(s): 80-6
Country/Region of Manufacture: USA
Freq Range (MHz):: 3.5-54 Mhz
Power (PEP watts):: 500/1500/5000
Length (ft):: 135

Excellent features:

*** Covers 80-40-20-17-15-12-10-6 meter ham bands

*** SWR < 2:1 on most bands, may require antenna tuner 80, 40 for full band use

*** 500 watts/1.5KW/5KW PEP (SSB-ICAS) options

*** Stainless Steel hardware for long life

*** Halyard Hoist for ease of installation

*** Insulated #14 wire for durability

*** High Strength insulators (may be black, white or gray)

*** 4:1 Balun and 1:1 Choke included in a single enclosure

Super convenient and quick – great for contest operation! Choose 500, 1500 or 5000 watt PEP (use 5KW model for digital modes over 1000 watts).

Unlike Buckmaster OCF antennas (at twice the price, and no WARC bands, 6 meter or 15 Meter operation, you can transmit and receive on 12,15 and 17 meters with our OCF - Better engineering and lower price - only from Palomar Engineers!

INSTALLATION

For best results support center at 30+ feet and ends over 15 feet. Angle of feed each side must be great than 45 degrees or 120 – 180 degrees total between each side preferred. Any length of 50 ohm feed line ok but longer feed lines over 50 feet may show reduced SWR on some bands due to losses in feed line and soil conductivity, nearby objects, etc. Due to local ground conditions, antenna height and feed line length, SWR may vary from samples shown and an antenna tuner may be required or some bands to bring SWR at end of feed line to acceptable levels. Overall length is 95+40 =135 feet.

FREE Shipping on orders over $100

Insulators may be black, grey or white depending on stock at hand when order is placed. Wire is stranded, insulated and black color.

5KW antennas are made to order and take approximately 10 days after order to ship.

SWR TECH NOTE:The SWR graphs shown are specific to the conditions listed including antenna height, configuration (flat top, inverted V, inverted L, etc.) and direction, feed line length and type, geographic location and soil condition, calibration and accuracy of SWR instruments used. Your SWR measurements will probably be different and manufacturer takes no responsibility or liability for these differences beyond the purchase price of the antenna.

Note if you like the band coverage of this antenna but don't quite have 135 feet available, then consider the BULLET-8006 with very similar band coverage but only needs 95 feet of wire that is end fed.

Testimonial:

Chris Miller – Facebook 2/20/22

PAL OCF8010 vs Myantennas OCf SWR jpg - SUPER CHOKER™

A tale of two very different antennas, and two very different companies... I started with the MyAntennas 75-10 strung across the top of a 15 foot hedge around my property, based on the company's claim on their website "Due to the High Impedance feed point, the antenna is less height-dependent. You can put it up at 10 or 50 feet in the air without much change in VSWR values."... Being new to the hobby and not getting the advertised SWR in this configuration, I reached out for help on the company's Facebook group... The owner berated me for not understanding how antennas work. I simply reminded him of the company's claim on their site. He would not reply to my emails, and kicked me out of the group... Fortunately there were a number of much more friendly and helpful people in that group that helped me to understand that height really does matter, despite the company's claim... So I used my drone to get the wire to the top of a tall palm tree on my property, and get very respectable performance out of the antenna... But being new, excited and curious, striving for knowledge and experience in the hobby, I wanted to see how the EFHW would compare to a similarly placed OCF... Palomar Engineers has multiple models that peaked my interest, so I reached out to the company to find out which model/configuration would work best. The owner of the company, Bob (AK6R) personally called me, asked questions about my location and my station, talked me through options, and explained to me the history and development of his "80-10 vertical radiator" model. This was the antenna he suggested based on the spacing and arrangement of palm trees at the QTH. Bob's willingness to share his knowledge and assistance was true to the spirit I have come to enjoy in this hobby... So over the weekend I contracted a tree service company to deploy the Palomar OCF just below the EFHW (You can see the ends of the two wires in the first photo, the EFHW terminating 5 or 6 feet above the OCF)... Performance is very similar where it counts as you can see from the SWR chart.... what's remarkable about the OCF is my noise floor drops 1 to 2 S units, which is huge for me, living in an urban environment where noise is obviously an issue... And of course the relatively flat SWR across the board, not just on points of resonance. I hope someone may find my experience between the two antenna types, or the two antenna companies, helpful. 73 KI6GEA


the ocf i purchased is the best working antenna i have ever had
wa6nrg john
NI5I: I was using a Buckmaster OCF, was given your 500 watt version second
hand, then bought your 1500 watt version from HRO last summer. I wanted
another. I love this antenna!
Save this product for later
Super-Choker™ Common Mode Feed Line Chokes

Sometimes you need a high power common mode choke that is super effective and the Super-Choker™ products fill this need very well.   All Super-Choker™ chokes use multiple turns through ferrite cores for higher choking impedance compared to our multi-bead sleeve chokes which only use one turn through multiple cores.  Different ferrite mixes and turns ratios are used to optimize choking impedance in the selected product frequency range.

Super-Choker™ chokes are manufactured with 1/2″ 52 ohm coax cable (rated for full amateur radio legal limit of 1500 watts continuous (or the capacity of the coax cable at the selected frequency – good for over 5KW on 4 MHz into a matched load for example) with PL-259 connectors that can be connected to your coax feed line with simple double female barrel connectors.

Super-Choker™ chokes are ideal for high power stations and are very effective for keeping common mode current off the feed line on verticals, dipoles, and loop antennas at their feed point and also for choking coax lines at the station input to reduce common mode noise picked up by the outside of the coax braid between the feed point and the station entrance.

 

Ferrite core kits are available separately if you want to supply your own coax feed line.

 

 

Super Choker™ Case History:

I run an 80 meter loop antenna about 30 feet in height and have previously been using a coaxial balun common mode choke of 25 turns of RG-213 on a 6 inch form attached about 6 feet under the corner feed point of the loop (configured in a triangle).  Using a Dentron 3000 antenna tuner I was able to tune all the ham bands and the lowest SWR was about 1.4 on most bands.  The antenna feed line was led away from the corner of the loop and was not under the loop.  Feed line length was about 105 feet as measured on the Aim 4170-TDR function.

I first placed a Super Choker™ 8010 at the antenna tuner leaving the coaxial balun in place.  As I retuned the antenna tuner, the first thing I noticed was that I could now tune down to 1.1:1 on 80, 40 and 20 meters and I could not do that before.  The noise level which had been running about S7 on 40 meters during the day had dropped to about S6 on my TS-870 receiver.  I was pleased that the reflected power was now almost nil and the noise level was lower. 

I then took the next step and replaced the coaxial balun and Super Choker 8010 with a Super Choker™ 16040 in series with a Super Choker 4010 for maximum choking power from 80-10meters.  The antenna tuning was about the same but now the SWR was 1.0:1 on 80-10 meters and the noise level on 40 was down to S5.  I tuned up on 20, 15 and 10 meters and worked a couple of JA’s and noticed that the noise level on 10 and 15 was not even S1 – something I had not experienced before on the 5 acre plot of land we call home. 

What a welcome relief to find such a simple solution to RF feedback I had experienced and I got a lower noise level to boot! 

Now to plan that 160 meter loop!  I wonder what Krusty ole Kurt would use?

Bob, AK6R