SUPER CHOKER™

MAXI-CHOKER Coax Line Isolator/Choke, 1-61 MHz, 1.5/3KW/5KW, up to -60 Db Common Mode Rejection, Static Bleeder Option

MC-1-1500
$89.95
In stock
1
Product Details
Brand: Palomar Engineers
MPN: MC-1-3000/MC-1-5000
Country/Region of Manufacture: United States
Effective Frequency Range (MHz): 1-61 (1.5KW, 3KW, 5KW)
PEP Power Rating (watts): 1500/3000/5000 to 61 MHz
Common Mode Attenuation (db): 15-42 (1.5KW), 20-48 dB (3KW), up to 60 dB (5KW)
Estimated Insertion Loss (db): .25 db
Input Connector Type: SO-239 female/N (option)
Output Connector Connector Type: SO-239 female/ N (option)
Ground Connector (Y/N): optional with static bleeder
Enclosure Size (LxWxH inches): 12" long, 2" diameter (3KW)/11" x 2-3/4" (5KW)

MAXI-CHOKER Features:

- Uses proprietary Multi-Mix, Multi-Core, Multi-Turn(TM) ferrite technology for maximum choking (up to -48 dB common mode noise rejection) and maximum bandwidth

- Choose 1.5 KW, 3 KW PEP or 5KW PEP for heavy duty digital modes up to legal limit, 50 ohm SO-239 connectors In/Out, 1-61 MHz, usable to 100 MHz

- Suppresses transmitter coax feed line radiation when installed at antenna feed point or reduces common mode receiver "noise" when installed at radio end of coax.

- Available with ground stud/static bleeder option for solving tough RFI issues

- Available with dual stud/wingnut output for ladder line interface

- Works for all coax fed antennas from 1.8-61 MHz (160-6 meters) - excellent for multi-band beams, verticals, dipoles and highly unbalanced off center fed antennas.

- 2-5 times more common mode noise rejection, wider bandwidth and higher power then competing filters

MAXI-CHOKER feed line chokes are used to suppress common mode current carried on the outside of the coax braid which is often responsible for receiver noise and RFI in the receiver/transmitter. These chokes are very useful for suppressing RFI common mode current at the antenna feed point, at 1/2 wavelength intervals along the coax feed line and also at the entrance to the radio station. This choke is available with a SO-239 input/output and ground/static bleeder stud (optional) for attachment to a ground rod. Use an isolator every 1/2 wavelength for the antenna operating frequency (include velocity factor in calculation). Use the ground lug option for long coax antenna feed lines (over 1/2 wavelength at the operating frequency of any antenna system in the near field of the coax).

Need a smaller power rating but with same, great common mode suppression? Try our 500 watt PEP rated Mini-Choker HERE

Production Note: Maxi-Choker may be in Black or White color depending upon available inventory at time of shipment.





Save this product for later
Super-Choker™ Common Mode Feed Line Chokes

Sometimes you need a high power common mode choke that is super effective and the Super-Choker™ products fill this need very well.   All Super-Choker™ chokes use multiple turns through ferrite cores for higher choking impedance compared to our multi-bead sleeve chokes which only use one turn through multiple cores.  Different ferrite mixes and turns ratios are used to optimize choking impedance in the selected product frequency range.

Super-Choker™ chokes are manufactured with 1/2″ 52 ohm coax cable (rated for full amateur radio legal limit of 1500 watts continuous (or the capacity of the coax cable at the selected frequency – good for over 5KW on 4 MHz into a matched load for example) with PL-259 connectors that can be connected to your coax feed line with simple double female barrel connectors.

Super-Choker™ chokes are ideal for high power stations and are very effective for keeping common mode current off the feed line on verticals, dipoles, and loop antennas at their feed point and also for choking coax lines at the station input to reduce common mode noise picked up by the outside of the coax braid between the feed point and the station entrance.

 

Ferrite core kits are available separately if you want to supply your own coax feed line.

 

 

Super Choker™ Case History:

I run an 80 meter loop antenna about 30 feet in height and have previously been using a coaxial balun common mode choke of 25 turns of RG-213 on a 6 inch form attached about 6 feet under the corner feed point of the loop (configured in a triangle).  Using a Dentron 3000 antenna tuner I was able to tune all the ham bands and the lowest SWR was about 1.4 on most bands.  The antenna feed line was led away from the corner of the loop and was not under the loop.  Feed line length was about 105 feet as measured on the Aim 4170-TDR function.

I first placed a Super Choker™ 8010 at the antenna tuner leaving the coaxial balun in place.  As I retuned the antenna tuner, the first thing I noticed was that I could now tune down to 1.1:1 on 80, 40 and 20 meters and I could not do that before.  The noise level which had been running about S7 on 40 meters during the day had dropped to about S6 on my TS-870 receiver.  I was pleased that the reflected power was now almost nil and the noise level was lower. 

I then took the next step and replaced the coaxial balun and Super Choker 8010 with a Super Choker™ 16040 in series with a Super Choker 4010 for maximum choking power from 80-10meters.  The antenna tuning was about the same but now the SWR was 1.0:1 on 80-10 meters and the noise level on 40 was down to S5.  I tuned up on 20, 15 and 10 meters and worked a couple of JA’s and noticed that the noise level on 10 and 15 was not even S1 – something I had not experienced before on the 5 acre plot of land we call home. 

What a welcome relief to find such a simple solution to RF feedback I had experienced and I got a lower noise level to boot! 

Now to plan that 160 meter loop!  I wonder what Krusty ole Kurt would use?

Bob, AK6R